PNX8950EH-Board: Unterschied zwischen den Versionen

Aus Chaostreff Chemnitz
Tesla (Diskussion | Beiträge)
Txt.file (Diskussion | Beiträge)
K Ebenen der Überschriften verbessert
 
(13 dazwischenliegende Versionen von 2 Benutzern werden nicht angezeigt)
Zeile 5: Zeile 5:
* Linux, Windows CE
* Linux, Windows CE


= hacken =
== hacken ==


== Erstinbetriebnahme/Test ==
=== Infos ===
 
Cable-Tuner: [http://www.dvedn.com/UploadFiles/2011624181226478.pdf CU1216]
 
=== Erstinbetriebnahme/Test ===


* unteren Scart-Anschluss mit Fernseher verbinden
* unteren Scart-Anschluss mit Fernseher verbinden
Zeile 15: Zeile 19:
* Fernseher zeigt Windows CE 5.0 Oberfläche
* Fernseher zeigt Windows CE 5.0 Oberfläche


== "Auslieferungszustand" herstellen ==
=== "Auslieferungszustand" herstellen ===


Um weiter basteln zu können, muss eine bestimmte Windows-Version installiert werden: [http://www.mikrocontroller.net/attachment/111731/reflash_wince.rar]
Um weiter basteln zu können, muss eine bestimmte Windows-Version installiert werden: [http://www.mikrocontroller.net/attachment/111731/reflash_wince.rar]
Zeile 32: Zeile 36:
* Windows starten: DIP-Schalter 1 wieder auf off und Reset (Taste hinten) + Einschalttaste
* Windows starten: DIP-Schalter 1 wieder auf off und Reset (Taste hinten) + Einschalttaste


== Neue Variante ==
=== Neue Variante ===


Es gibt eine relativ sichere Variante. Dazu wird das Elecard-Image benötigt. Es wird gleich das große U-Boot geflasht und bei Bedarf das Elecard-Linux.
Es gibt eine relativ sichere Variante. Dazu wird das Elecard-Image benötigt. Es wird gleich das große U-Boot geflasht und bei Bedarf das Elecard-Linux.
Zeile 40: Zeile 44:
Anleitung: [http://linux-party.at/Schnelleinstieg]
Anleitung: [http://linux-party.at/Schnelleinstieg]


=== Flashen ===
==== Flashen ====


* DIP-Schalter 1 auf off
* DIP-Schalter 1 auf off
Zeile 57: Zeile 61:
Board kann jetzt U-Boot und Linux starten.
Board kann jetzt U-Boot und Linux starten.


=== Linux starten ===
==== Linux starten ====


Beim Neustart kommen noch 3 Zeilen des Flashers auf der J2. Das richtige U-Boot kommt allerdings auf J33:
Beim Neustart kommen noch 3 Zeilen des Flashers auf der J2. Das richtige U-Boot kommt allerdings auf J33:
Zeile 75: Zeile 79:
* nach erfolgreichem Bezug der Adresse ist die Konsole verfügbar
* nach erfolgreichem Bezug der Adresse ist die Konsole verfügbar


=== Linux automatisch starten ===
==== Linux automatisch starten ====


Damit Linux nach dem Einschalten automatisch startet muss U-Boot konfiguriert werden.
Damit Linux nach dem Einschalten automatisch startet muss U-Boot konfiguriert werden.
Zeile 90: Zeile 94:
* wenn U-Boot-Fehlermeldungen kommen, setenv nandboot nochmal durchführen, am besten Zeile kopieren, darauf achten, dass keine Leerzeichen oder ähnliches angehängt werden.
* wenn U-Boot-Fehlermeldungen kommen, setenv nandboot nochmal durchführen, am besten Zeile kopieren, darauf achten, dass keine Leerzeichen oder ähnliches angehängt werden.


=== neues rootFS ===
==== neues rootFS ====


Es ist möglich ein Debian-rootFS mit dem Elecard-Kernel zu verwenden. Das rootFS gibt es hier: [http://linux-party.at/tiki-download_file.php?fileId=6]
Es ist möglich ein Debian-rootFS mit dem Elecard-Kernel zu verwenden. Das rootFS gibt es hier: [http://linux-party.at/tiki-download_file.php?fileId=6]
Zeile 98: Zeile 102:
* Stick an Board anstecken
* Stick an Board anstecken
* Elecard-Kernel booten
* Elecard-Kernel booten
* ssh auf Board mit root/vdr
* ssh auf Board mit root/vdr (ip-Adresse? -> die vom dhcp-Server)
* Ausschalten: reboot
* niemals direkt ausschalten oder reset drücken, sonst geht das rootFS kaputt und das Bpoard startet nicht mehr -> siehe Debug


=== Debug ===
==== Debug ====


Wenn man etwas nicht funktioniert:
Wenn man etwas nicht funktioniert:
Zeile 106: Zeile 112:
* "unhandled paging request on adress 00000000" beim Boot: rootFS ist beschädigt, einfach check mit gparted und es funktioniert wieder (wichtig: Stick safely removen)
* "unhandled paging request on adress 00000000" beim Boot: rootFS ist beschädigt, einfach check mit gparted und es funktioniert wieder (wichtig: Stick safely removen)


== Alte Variante ==
=== Alte Variante ===


Beschreibung unvollständig. Bitte nicht versuchen, die Neue Variante funktioniert.
Beschreibung unvollständig. Bitte nicht versuchen, die Neue Variante funktioniert.


=== kleines U-Boot flashen ===
==== kleines U-Boot flashen ====


Um Linux zu starten wird ein Bootloader gebraucht. Dieser kann allerdings zu große um jetzt aufgespielt zu werden. Es wird deshalb erst ein Kleiner installiert, danach der Große.
Um Linux zu starten wird ein Bootloader gebraucht. Dieser kann allerdings zu große um jetzt aufgespielt zu werden. Es wird deshalb erst ein Kleiner installiert, danach der Große.
Zeile 125: Zeile 131:
* dritter Button: verändertes Windows-CE, nicht unbedingt flashen, soll flashme automatisch starten, bootet nicht bis zur grafischen Oberfläche, sondern hängt im Ladebalken fest
* dritter Button: verändertes Windows-CE, nicht unbedingt flashen, soll flashme automatisch starten, bootet nicht bis zur grafischen Oberfläche, sondern hängt im Ladebalken fest


=== großes U-Boot flashen ===
==== großes U-Boot flashen ====


Nachdem nun das kleine U-Boot drauf ist, kann das große U-Boot mit mehr Funktionen aufgespielt werden. Dazu muss das kleine U-Boot gestartet werden:
Nachdem nun das kleine U-Boot drauf ist, kann das große U-Boot mit mehr Funktionen aufgespielt werden. Dazu muss das kleine U-Boot gestartet werden:
Zeile 131: Zeile 137:
* DIP-Schalter 1 auf on
* DIP-Schalter 1 auf on
* Board einschalten (Taste an Bedienteil)
* Board einschalten (Taste an Bedienteil)
== Nach der Linux-Installation ==
=== richtig ===
<nowiki>
Determined physical RAM map:
memory: 07000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Built 1 zonelists.  Total pages: 28448
Kernel command line: console=ttyS1,38400n8 stb810_display=pal nomainapp=1 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw
Primary instruction cache 16kB, physically tagged, 2-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (23 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 512 (order: 9, 2048 bytes)
Using 250.714 MHz high precision timer.
Console: colour dummy device 80x25
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 107648k/114688k available (2841k kernel code, 6996k reserved, 518k data, 2044k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Time: MIPS clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NTFS driver 2.1.28 [Flags: R/O].
JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler anticipatory registered (default)
Register GPIO SPI device
Serial: PNX8XXX driver $Revision: 1.2 $
pnx8xxx-uart: ttyS0 at MMIO 0xbbe4a000 (irq = 27) is a PNX8XXX
pnx8xxx-uart: ttyS1 at MMIO 0xbbe4b000 (irq = 28) is a PNX8XXX
natsemi dp8381x driver, version 2.1, Sept 11, 2006
  originally by Donald Becker <becker@scyld.com>
  http://www.scyld.com/network/natsemi.html
  2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
PCI: Enabling device 0000:00:0a.0 (0006 -> 0007)
natsemi eth0: NatSemi DP8381[56] at 0x20092000 (0000:00:0a.0), 00:17:31:fb:e4:cd, IRQ 55, port TP.
Driver for NAND Flash on the PNX8550 XIO bus (Mar 15 2010-17:54:27)
Auto detected a >= 64MByte device on a 8 bit bus
NAND device: Manufacturer ID: 0xad, Chip ID: 0x76 (Hynix NAND 64MiB 3,3V 8-bit)
Scanning device for bad blocks
Creating 8 MTD partitions on "NAND 64MiB 3,3V 8-bit":
0x00000000-0x00004000 : "microBTM"
0x00004000-0x00084000 : "U-Boot"
0x00084000-0x0008c000 : "Env"
0x0008c000-0x00094000 : "bbt"
0x00094000-0x00894000 : "Linux"
0x00894000-0x03b94000 : "ROMFS"
0x03c00000-0x03ff8000 : "WinCE"
0x03ff8000-0x04000000 : "Info"
ehci_hcd 0000:00:09.2: EHCI Host Controller
ehci_hcd 0000:00:09.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:09.2: irq 55, io mem 0x20093200
ehci_hcd 0000:00:09.2: USB 2.0 started, EHCI 0.95, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
pnx8550-ohci pnx8550-ohci: PNX8550 OHCI
pnx8550-ohci pnx8550-ohci: new USB bus registered, assigned bus number 2
pnx8550-ohci pnx8550-ohci: irq 13, io mem 0x1be48000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd 0000:00:09.0: OHCI Host Controller
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:09.0: irq 55, io mem 0x20090000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ohci_hcd 0000:00:09.1: OHCI Host Controller
ohci_hcd 0000:00:09.1: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:09.1: irq 55, io mem 0x20091000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
USB Universal Host Controller Interface driver v3.0
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Bridge firewalling registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
eth0: DSPCFG accepted after 0 usec.
Sending DHCP requests .....<6>eth0: Autonegotiation advertising 0x5e1  partner 0xcde1.
eth0: link up.
eth0: Setting full-duplex based on negotiated link capability.
.<5>eth0: increased tx threshold, txcfg 0xd0f01004.
timed out!
IP-Config: Reopening network devices...
eth0: DSPCFG accepted after 0 usec.
eth0: link up.
eth0: Setting full-duplex based on negotiated link capability.
Sending DHCP requests .<5>eth0: increased tx threshold, txcfg 0xd0f01004.
., OK
IP-Config: Got DHCP answer from 192.168.1.1, my address is 192.168.1.171
IP-Config: Complete:
      device=eth0, addr=192.168.1.171, mask=255.255.255.0, gw=192.168.1.1,
    host=192.168.1.171, domain=lan, nis-domain=(none),
    bootserver=192.168.1.1, rootserver=192.168.1.1, rootpath=
Freeing unused kernel memory: 2044k freed
Algorithmics/MIPS FPU Emulator v1.5
Loading profile...  done
Mount fstab... done
Remount / read-write... done
Mounting new Root.
enabling SATA modules...sata_sil 0000:00:08.0: Applying R_ERR on DMA activate FIS errata fix
ata1: SATA max UDMA/100 cmd 0xc0058080 ctl 0xc005808a bmdma 0xc0058000 irq 55
ata2: SATA max UDMA/100 cmd 0xc00580c0 ctl 0xc00580ca bmdma 0xc0058008 irq 55
scsi0 : sata_sil
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: ATA-8: Hitachi HTS545050B9A300, PB4OC66G, max UDMA/133
ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/100
scsi1 : sata_sil
ata2: SATA link down (SStatus 0 SControl 310)
scsi 0:0:0:0: Direct-Access    ATA      Hitachi HTS54505 PB4O PQ: 0 ANSI: 5
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
sda: Write Protect is off
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
sda: Write Protect is off
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3
sd 0:0:0:0: Attached scsi disk sda
done
Creating device nodes...done
Setup mdev as hotplug handler... done
Set log level...
Populate /dev... Load luddite and gpio/mmio/rtc...Get display mode and load i2c and fb modules... Detect GPIO function...done
Get System ID...
Restore hotplug handler... done
Restore log level...
Unloading modules...
Shutting down RTC driver
Shutting down PNX8550 MMIO Driver
Shutting down PNX8550 GPIO driver
Shutting down NXP /proc entries driver
done
done
Mount nfs root /dev/sda1... kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
done
Switch root
INIT: version 2.86 booting
.udev/ already exists on the static /dev! (warning).
Starting the hotplug events dispatcher: udevdudevd[431]: main: the kernel does not support inotify, udevd can't monitor rules file changes
.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...udevd-event[506]: rename_netif: error changing netif name eth0 to eth1: Device or resource busy
Registering SPI driver
Register ProSLIC driver
done.
Setting the system clock.
Cannot access the Hardware Clock via any known method.
Use the --debug option to see the details of our search for an access method.
Unable to set System Clock to: Sat Jan 1 00:00:26 UTC 2005 (warning).
Activating swap...done.
Setting the system clock.
Cannot access the Hardware Clock via any known method.
Use the --debug option to see the details of our search for an access method.
Unable to set System Clock to: Sat Jan 1 00:00:27 UTC 2005 (warning).
Cleaning up ifupdown....
Loading kernel modules...done.
Checking file systems...fsck 1.41.3 (12-Oct-2008)
done.
Setting kernel variables (/etc/sysctl.conf)...done.
Mounting local filesystems...kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda2, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
done.
Activating swapfile swap...done.
Setting up networking....
Configuring network interfaces...done.
Luddite version 3, exported  Mon Apr 25 10:40:08 BST 2005
TM0: detected clock 270000000
lud_core: Registering devfs device 0/lud
TM1: detected clock 270000000
lud_core: Registering devfs device 1/lud
NXP /proc entries driver (Aug 13 2007-11:59:40)
dspinfo: Initialising DSP Info Driver
PNX8550 MMIO Driver (Aug 13 2007-11:59:38)
dspmem: Initialising DSP memory Driver
Philips PNX8550 Demux HW driver (Aug 13 2007-11:59:14)
DVB: registering new adapter (pnx8550vmsp0).
DVB: registering new adapter (pnx8550vmsp1).
DVB: registering new adapter (pnx8550pdma0).
DVB: registering new adapter (pnx8550pdma1).
NXP PNX8550 DVB adapter driver
Analog Backend driver (Aug 13 2007-11:59:55)
AK470X (AV Scart switch) driver (Aug 13 2007-11:59:57) - Device AK4706 Loopthrough disabled
Using specified video mode (PAL-CVBS)
vdenc0: PNX8550 Internal Vdenc video denc device
Dbg driver (Feb 20 2008-12:40:20)
TriMedia RPC driver
Debug Buffer Print driver (Aug 13 2007-11:59:09)
RTC driver (Aug 13 2007-11:59:41)
PNX8550 GPIO driver (Aug 13 2007-11:59:32)
SAA8510 (Anabel) driver
Using specified video mode (PAL-RGB)
vdenc1: PNX8510 Driver video denc device
STB-810 ALSA Audio Driver (Aug 13 2007-11:59:07)
pnxdraw: Initialised (Compiled Aug 13 2007-11:59:22)
Cannot open luddite device - Error = -1
open tmdev: No such file or directory
Cannot open luddite device - Error = -1
open tmdev: No such file or directory
INIT: Entering runlevel: 2
Starting enhanced syslogd: rsyslogd.
Starting OpenBSD Secure Shell server: sshd.
##################################################
## LIRC IS NOT CONFIGURED                      ##
##                                              ##
## read /usr/share/doc/lirc/html/configure.html ##
##################################################
Additional hint: Either /etc/lirc/lircd.conf or
/etc/lirc/hardware.conf doesn't exist or either
of the two has the string UNCONFIGURED in it at
some important place. Try: 'dpkg-reconfigure lirc'
Starting lirc daemon:.
Starting Linux Video Disk Recorder: vdr
Searching for plugins (VDR 1.6.0-2/1.6.0) (cache hit): xvdr streamdev-server.
Starting VDR Webadministration interface: - aborted (to enable the daemon, edit /etc/default/vdradmin-am)Starting periodic command scheduler: crond.
eth0: increased tx threshold, txcfg 0xd0f01006.
eth0: increased tx threshold, txcfg 0xd0f01008.
</nowiki>
=== falsch ===
<nowiki>
  Data Size:    3233500 Bytes = 3.1 MiB
  Load Address: 80060000
  Entry Point:  803a9000
  Verifying Checksum ... OK
  Uncompressing Kernel Image ... OK
Starting kernel ...
Determined physical RAM map:
memory: 07000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Built 1 zonelists.  Total pages: 28448
Kernel command line: console=ttyS1,38400n8 stb810_display=pal nomainapp=1 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw
Primary instruction cache 16kB, physically tagged, 2-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (23 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 512 (order: 9, 2048 bytes)
Using 250.714 MHz high precision timer.
Linux version 2.6.21.3PNX8550 (root@smithy) (gcc version 4.0.0 (DENX ELDK 4.0 4.0.0)) #1743 Fri Feb 11 10:49:15 OMST 2011
Setting initial splash screen display mode SD (50Hz)
CPU revision is: 00061200
Determined physical RAM map:
memory: 07000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Built 1 zonelists.  Total pages: 28448
Kernel command line: console=ttyS1,38400n8 stb810_display=pal nomainapp=1 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw
Primary instruction cache 16kB, physically tagged, 2-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (23 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 512 (order: 9, 2048 bytes)
Using 250.714 MHz high precision timer.
Console: colour dummy device 80x25
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 107648k/114688k available (2841k kernel code, 6996k reserved, 518k data, 2044k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Time: MIPS clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NTFS driver 2.1.28 [Flags: R/O].
JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler anticipatory registered (default)
Register GPIO SPI device
Serial: PNX8XXX driver $Revision: 1.2 $
pnx8xxx-uart: ttyS0 at MMIO 0xbbe4a000 (irq = 27) is a PNX8XXX
pnx8xxx-uart: ttyS1 at MMIO 0xbbe4b000 (irq = 28) is a PNX8XXX
natsemi dp8381x driver, version 2.1, Sept 11, 2006
  originally by Donald Becker <becker@scyld.com>
  http://www.scyld.com/network/natsemi.html
  2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
PCI: Enabling device 0000:00:0a.0 (0006 -> 0007)
natsemi eth0: NatSemi DP8381[56] at 0x20092000 (0000:00:0a.0), 00:17:31:fb:e4:cd, IRQ 55, port TP.
Driver for NAND Flash on the PNX8550 XIO bus (Mar 15 2010-17:54:27)
Auto detected a >= 64MByte device on a 8 bit bus
NAND device: Manufacturer ID: 0xad, Chip ID: 0x76 (Hynix NAND 64MiB 3,3V 8-bit)
Scanning device for bad blocks
Creating 8 MTD partitions on "NAND 64MiB 3,3V 8-bit":
0x00000000-0x00004000 : "microBTM"
0x00004000-0x00084000 : "U-Boot"
0x00084000-0x0008c000 : "Env"
0x0008c000-0x00094000 : "bbt"
0x00094000-0x00894000 : "Linux"
0x00894000-0x03b94000 : "ROMFS"
0x03c00000-0x03ff8000 : "WinCE"
0x03ff8000-0x04000000 : "Info"
ehci_hcd 0000:00:09.2: EHCI Host Controller
ehci_hcd 0000:00:09.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:09.2: irq 55, io mem 0x20093200
ehci_hcd 0000:00:09.2: USB 2.0 started, EHCI 0.95, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
pnx8550-ohci pnx8550-ohci: PNX8550 OHCI
pnx8550-ohci pnx8550-ohci: new USB bus registered, assigned bus number 2
pnx8550-ohci pnx8550-ohci: irq 13, io mem 0x1be48000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd 0000:00:09.0: OHCI Host Controller
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:09.0: irq 55, io mem 0x20090000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ohci_hcd 0000:00:09.1: OHCI Host Controller
ohci_hcd 0000:00:09.1: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:09.1: irq 55, io mem 0x20091000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
USB Universal Host Controller Interface driver v3.0
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Bridge firewalling registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
eth0: DSPCFG accepted after 0 usec.
eth0: link up.
eth0: Setting full-duplex based on negotiated link capability.
Sending DHCP requests .<5>eth0: increased tx threshold, txcfg 0xd0f01004.
..... timed out!
IP-Config: Reopening network devices...
eth0: DSPCFG accepted after 0 usec.
eth0: link up.
eth0: Setting full-duplex based on negotiated link capability.
Sending DHCP requests .<5>eth0: increased tx threshold, txcfg 0xd0f01004.
., OK
IP-Config: Got DHCP answer from 192.168.1.1, my address is 192.168.1.171
IP-Config: Complete:
      device=eth0, addr=192.168.1.171, mask=255.255.255.0, gw=192.168.1.1,
    host=192.168.1.171, domain=lan, nis-domain=(none),
    bootserver=192.168.1.1, rootserver=192.168.1.1, rootpath=
Freeing unused kernel memory: 2044k freed
Algorithmics/MIPS FPU Emulator v1.5
Loading profile...  done
Mount fstab... done
Remount / read-write... done
Mounting new Root.
enabling SATA modules...sata_sil 0000:00:08.0: Applying R_ERR on DMA activate FIS errata fix
ata1: SATA max UDMA/100 cmd 0xc0058080 ctl 0xc005808a bmdma 0xc0058000 irq 55
ata2: SATA max UDMA/100 cmd 0xc00580c0 ctl 0xc00580ca bmdma 0xc0058008 irq 55
scsi0 : sata_sil
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: ATA-8: Hitachi HTS545050B9A300, PB4OC66G, max UDMA/133
ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/100
scsi1 : sata_sil
ata2: SATA link down (SStatus 0 SControl 310)
scsi 0:0:0:0: Direct-Access    ATA      Hitachi HTS54505 PB4O PQ: 0 ANSI: 5
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
sda: Write Protect is off
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
sda: Write Protect is off
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3
sd 0:0:0:0: Attached scsi disk sda
done
Creating device nodes...done
Setup mdev as hotplug handler... done
Set log level...
Populate /dev... Load luddite and gpio/mmio/rtc...Get display mode and load i2c and fb modules... Detect GPIO function...done
Get System ID...
Restore hotplug handler... done
Restore log level...
Unloading modules...
CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == 801f30dc, ra == c00729e4
Oops[#1]:
Cpu 0
$ 0  : 00000000 10008401 00100100 00000000
$ 4  : 00000000 00000000 c0064304 86e39ed8
$ 8  : 803896b0 86e39ee1 800a86a8 0000000c
$12  : 43545262 2aab2800 00000000 2aab2800
$16  : c0072e80 c0072e74 00000087 00000480
$20  : 00000000 00000002 00000000 00000003
$24  : 00000000 2acec13c
$28  : 86e38000 86e39e80 7f9bec20 c00729e4
Hi    : 00000372
Lo    : 0002c316
epc  : 801f30dc    Tainted: P
ra    : c00729e4 Status: 10008403    KERNEL EXL IE
Cause : 1080000c
BadVA : 00000000
PrId  : 00061200
Modules linked in: sysid(P) i2c_algo_IP0105 i2c_algo_IP3203 phStbRTC phStbMmio phStbGpio phStbProc lud_pnx8550 lud_core sata_sil libata
Process exe (pid: 312, threadinfo=86e38000, task=811027f0)
Stack : 805b0000 805b0000 0000004f 00030002 80390000 c0072f20 80390000 c00729e4
        805b4e50 80099104 8008dfc0 0002ad9b 800a8844 800a86d4 805b4e50 8008a36c
        86e39ec0 86e39ec0 00000000 c0072f20 00000480 86e39ec8 74536870 43545262
        00000200 00000001 10008400 10002ea8 2aafdcb8 004068c8 10008400 8008a540
        00000000 80096090 7f9bede1 00000001 009bed08 00000480 7f9bede1 00000001
        ...
Call Trace:[<c00729e4>][<80099104>][<8008dfc0>][<800a8844>][<800a86d4>][<8008a36c>][<8008a540>][<80096090>][<80069f00>][<80061d80>]
Code: 8e030000  3c020010  34420100 <ac830000> ae020000  3c020020  34420200  ac640004  ae020004
Shutting down PNX8550 MMIO Driver
Shutting down PNX8550 GPIO driver
Shutting down NXP /proc entries driver
done
done
Mount nfs root /dev/sda1... kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
done
Switch root
INIT: version 2.86 booting
.udev/ already exists on the static /dev! (warning).
Starting the hotplug events dispatcher: udevdudevd[425]: main: the kernel does not support inotify, udevd can't monitor rules file changes
.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...udevd-event[493]: rename_netif: error changing netif name eth0 to eth1: Device or resource busy
Registering SPI driver
Register ProSLIC driver
à
U-Boot 2011.09-00000-gf54ce7f-dirty (Dec 20 2011 - 12:36:29)
DRAM:  128 MiB
NAND:  NAND device: Manufacturer ID: 0xad, Chip ID: 0x76 (Hynix NAND 64MiB 3,3V 8-bit)
64 MiB
Bad block table at page 1120, version 0x01
Bad block table at page 1152, version 0x01
In:    serial
Out:  serial
Err:  serial
Net:  natsemi: EEPROM contents:
d008 0400 0b34 00f3 0000 0000 0000 8b80 7d98 66f2 0000 aae2
natsemi: MAC-Address: 0:17:31:FB:E4:CD
dp83815#0
Welcome to the pollinux board v1.1
Hit any key to stop autoboot:  0
Loading from nand0, offset 0x94000
  Image Name:  Elecard Linux 2.6
  Created:      2011-12-07  16:01:46 UTC
  Image Type:  MIPS Elecard Linux Kernel Image (gzip compressed)
  Data Size:    3233500 Bytes = 3.1 MiB
  Load Address: 80060000
  Entry Point:  803a9000
** Too many args (max. 16) **
** Too many args (max. 16) **
## Booting kernel from Legacy Image at 82000000 ...
  Image Name:  Elecard Linux 2.6
  Created:      2011-12-07  16:01:46 UTC
  Image Type:  MIPS Elecard Linux Kernel Image (gzip compressed)
  Data Size:    3233500 Bytes = 3.1 MiB
  Load Address: 80060000
  Entry Point:  803a9000
  Verifying Checksum ... OK
  Uncompressing Kernel Image ... OK
Starting kernel ...
Determined physical RAM map:
memory: 07000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Built 1 zonelists.  Total pages: 28448
Kernel command line: console=ttyS1,38400n8 stb810_display=pal nomainapp=1 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw
Primary instruction cache 16kB, physically tagged, 2-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (23 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 512 (order: 9, 2048 bytes)
Using 250.714 MHz high precision timer.
Linux version 2.6.21.3PNX8550 (root@smithy) (gcc version 4.0.0 (DENX ELDK 4.0 4.0.0)) #1743 Fri Feb 11 10:49:15 OMST 2011
Setting initial splash screen display mode SD (50Hz)
CPU revision is: 00061200
Determined physical RAM map:
memory: 07000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Built 1 zonelists.  Total pages: 28448
Kernel command line: console=ttyS1,38400n8 stb810_display=pal nomainapp=1 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw
Primary instruction cache 16kB, physically tagged, 2-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (23 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 512 (order: 9, 2048 bytes)
Using 250.714 MHz high precision timer.
Console: colour dummy device 80x25
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 107648k/114688k available (2841k kernel code, 6996k reserved, 518k data, 2044k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Time: MIPS clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NTFS driver 2.1.28 [Flags: R/O].
JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler anticipatory registered (default)
Register GPIO SPI device
Serial: PNX8XXX driver $Revision: 1.2 $
pnx8xxx-uart: ttyS0 at MMIO 0xbbe4a000 (irq = 27) is a PNX8XXX
pnx8xxx-uart: ttyS1 at MMIO 0xbbe4b000 (irq = 28) is a PNX8XXX
natsemi dp8381x driver, version 2.1, Sept 11, 2006
  originally by Donald Becker <becker@scyld.com>
  http://www.scyld.com/network/natsemi.html
  2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
PCI: Enabling device 0000:00:0a.0 (0006 -> 0007)
natsemi eth0: NatSemi DP8381[56] at 0x20092000 (0000:00:0a.0), 00:17:31:fb:e4:cd, IRQ 55, port TP.
Driver for NAND Flash on the PNX8550 XIO bus (Mar 15 2010-17:54:27)
Auto detected a >= 64MByte device on a 8 bit bus
NAND device: Manufacturer ID: 0xad, Chip ID: 0x76 (Hynix NAND 64MiB 3,3V 8-bit)
Scanning device for bad blocks
Creating 8 MTD partitions on "NAND 64MiB 3,3V 8-bit":
0x00000000-0x00004000 : "microBTM"
0x00004000-0x00084000 : "U-Boot"
0x00084000-0x0008c000 : "Env"
0x0008c000-0x00094000 : "bbt"
0x00094000-0x00894000 : "Linux"
0x00894000-0x03b94000 : "ROMFS"
0x03c00000-0x03ff8000 : "WinCE"
0x03ff8000-0x04000000 : "Info"
ehci_hcd 0000:00:09.2: EHCI Host Controller
ehci_hcd 0000:00:09.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:09.2: irq 55, io mem 0x20093200
ehci_hcd 0000:00:09.2: USB 2.0 started, EHCI 0.95, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
pnx8550-ohci pnx8550-ohci: PNX8550 OHCI
pnx8550-ohci pnx8550-ohci: new USB bus registered, assigned bus number 2
pnx8550-ohci pnx8550-ohci: irq 13, io mem 0x1be48000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd 0000:00:09.0: OHCI Host Controller
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:09.0: irq 55, io mem 0x20090000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ohci_hcd 0000:00:09.1: OHCI Host Controller
ohci_hcd 0000:00:09.1: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:09.1: irq 55, io mem 0x20091000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
USB Universal Host Controller Interface driver v3.0
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Bridge firewalling registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
eth0: DSPCFG accepted after 0 usec.
eth0: link up.
eth0: Setting full-duplex based on negotiated link capability.
Sending DHCP requests .<5>eth0: increased tx threshold, txcfg 0xd0f01004.
..... timed out!
IP-Config: Reopening network devices...
eth0: DSPCFG accepted after 0 usec.
eth0: link up.
eth0: Setting full-duplex based on negotiated link capability.
Sending DHCP requests .<5>eth0: increased tx threshold, txcfg 0xd0f01004.
., OK
IP-Config: Got DHCP answer from 192.168.1.1, my address is 192.168.1.171
IP-Config: Complete:
      device=eth0, addr=192.168.1.171, mask=255.255.255.0, gw=192.168.1.1,
    host=192.168.1.171, domain=lan, nis-domain=(none),
    bootserver=192.168.1.1, rootserver=192.168.1.1, rootpath=
Freeing unused kernel memory: 2044k freed
Algorithmics/MIPS FPU Emulator v1.5
Loading profile...  done
Mount fstab... done
Remount / read-write... done
Mounting new Root.
enabling SATA modules...sata_sil 0000:00:08.0: Applying R_ERR on DMA activate FIS errata fix
ata1: SATA max UDMA/100 cmd 0xc0058080 ctl 0xc005808a bmdma 0xc0058000 irq 55
ata2: SATA max UDMA/100 cmd 0xc00580c0 ctl 0xc00580ca bmdma 0xc0058008 irq 55
scsi0 : sata_sil
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: ATA-8: Hitachi HTS545050B9A300, PB4OC66G, max UDMA/133
ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/100
scsi1 : sata_sil
ata2: SATA link down (SStatus 0 SControl 310)
scsi 0:0:0:0: Direct-Access    ATA      Hitachi HTS54505 PB4O PQ: 0 ANSI: 5
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
sda: Write Protect is off
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
sda: Write Protect is off
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3
sd 0:0:0:0: Attached scsi disk sda
done
Creating device nodes...done
Setup mdev as hotplug handler... done
Set log level...
Populate /dev... Load luddite and gpio/mmio/rtc...Get display mode and load i2c and fb modules... Detect GPIO function...done
Get System ID...
Restore hotplug handler... done
Restore log level...
Unloading modules...
CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == 801f30dc, ra == c00729e4
Oops[#1]:
Cpu 0
$ 0  : 00000000 10008401 00100100 00000000
$ 4  : 00000000 00000000 c0064304 8110fed8
$ 8  : 803896b0 8110fee1 800a86a8 0000000c
$12  : 43545262 2aab2800 00000000 2aab2800
$16  : c0072e80 c0072e74 00000087 00000480
$20  : 00000000 00000002 00000000 00000003
$24  : 00000000 2acec13c
$28  : 8110e000 8110fe80 7fdb3c20 c00729e4
Hi    : 00000372
Lo    : 0002c316
epc  : 801f30dc    Tainted: P
ra    : c00729e4 Status: 10008403    KERNEL EXL IE
Cause : 1080000c
BadVA : 00000000
PrId  : 00061200
Modules linked in: sysid(P) i2c_algo_IP0105 i2c_algo_IP3203 phStbRTC phStbMmio phStbGpio phStbProc lud_pnx8550 lud_core sata_sil libata
Process exe (pid: 312, threadinfo=8110e000, task=86d9b7f0)
Stack : 805b0000 805b0000 0000004f 00030002 80390000 c0072f20 80390000 c00729e4
        805b4e50 80099104 8008dfc0 0002ad9b 800a8844 800a86d4 805b4e50 8008a36c
        8110fec0 8110fec0 00000000 c0072f20 00000480 8110fec8 74536870 43545262
        00000200 00000001 10008400 10002ed8 2aafdcb8 004068e0 10008400 8008a540
        00000000 80096090 7fdb3de1 00000001 00db3d08 00000480 7fdb3de1 00000001
        ...
Call Trace:[<c00729e4>][<80099104>][<8008dfc0>][<800a8844>][<800a86d4>][<8008a36c>][<8008a540>][<80096090>][<80069f00>][<80061d80>]
Code: 8e030000  3c020010  34420100 <ac830000> ae020000  3c020020  34420200  ac640004  ae020004
Shutting down PNX8550 MMIO Driver
Shutting down PNX8550 GPIO driver
Shutting down NXP /proc entries driver
done
done
Mount nfs root /dev/sda1... kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
done
Switch root
INIT: version 2.86 booting
.udev/ already exists on the static /dev! (warning).
Starting the hotplug events dispatcher: udevdudevd[425]: main: the kernel does not support inotify, udevd can't monitor rules file changes
.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...udevd-event[497]: rename_netif: error changing netif name eth0 to eth1: Device or resource busy
Registering SPI driver
Register ProSLIC driver
à
U-Boot 2011.09-00000-gf54ce7f-dirty (Dec 20 2011 - 12:36:29)
DRAM:  128 MiB
NAND:  NAND device: Manufacturer ID: 0xad, Chip ID: 0x76 (Hynix NAND 64MiB 3,3V 8-bit)
64 MiB
Bad block table at page 1120, version 0x01
Bad block table at page 1152, version 0x01
In:    serial
Out:  serial
Err:  serial
Net:  natsemi: EEPROM contents:
d008 0400 0b34 00f3 0000 0000 0000 8b80 7d98 66f2 0000 aae2
natsemi: MAC-Address: 0:17:31:FB:E4:CD
dp83815#0
Welcome to the pollinux board v1.1
Hit any key to stop autoboot:  0
Loading from nand0, offset 0x94000
  Image Name:  Elecard Linux 2.6
  Created:      2011-12-07  16:01:46 UTC
  Image Type:  MIPS Elecard Linux Kernel Image (gzip compressed)
  Data Size:    3233500 Bytes = 3.1 MiB
  Load Address: 80060000
  Entry Point:  803a9000
** Too many args (max. 16) **
** Too many args (max. 16) **
## Booting kernel from Legacy Image at 82000000 ...
  Image Name:  Elecard Linux 2.6
  Created:      2011-12-07  16:01:46 UTC
  Image Type:  MIPS Elecard Linux Kernel Image (gzip compressed)
  Data Size:    3233500 Bytes = 3.1 MiB
  Load Address: 80060000
  Entry Point:  803a9000
  Verifying Checksum ... OK
  Uncompressing Kernel Image ... OK
Starting kernel ...
Determined physical RAM map:
memory: 07000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Built 1 zonelists.  Total pages: 28448
Kernel command line: console=ttyS1,38400n8 stb810_display=pal nomainapp=1 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw
Primary instruction cache 16kB, physically tagged, 2-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (23 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 512 (order: 9, 2048 bytes)
Using 250.714 MHz high precision timer.
Linux version 2.6.21.3PNX8550 (root@smithy) (gcc version 4.0.0 (DENX ELDK 4.0 4.0.0)) #1743 Fri Feb 11 10:49:15 OMST 2011
Setting initial splash screen display mode SD (50Hz)
CPU revision is: 00061200
Determined physical RAM map:
memory: 07000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Built 1 zonelists.  Total pages: 28448
Kernel command line: console=ttyS1,38400n8 stb810_display=pal nomainapp=1 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw
Primary instruction cache 16kB, physically tagged, 2-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (23 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 512 (order: 9, 2048 bytes)
Using 250.714 MHz high precision timer.
Console: colour dummy device 80x25
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 107648k/114688k available (2841k kernel code, 6996k reserved, 518k data, 2044k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Time: MIPS clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NTFS driver 2.1.28 [Flags: R/O].
JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler anticipatory registered (default)
Register GPIO SPI device
Serial: PNX8XXX driver $Revision: 1.2 $
pnx8xxx-uart: ttyS0 at MMIO 0xbbe4a000 (irq = 27) is a PNX8XXX
pnx8xxx-uart: ttyS1 at MMIO 0xbbe4b000 (irq = 28) is a PNX8XXX
natsemi dp8381x driver, version 2.1, Sept 11, 2006
  originally by Donald Becker <becker@scyld.com>
  http://www.scyld.com/network/natsemi.html
  2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
PCI: Enabling device 0000:00:0a.0 (0006 -> 0007)
natsemi eth0: NatSemi DP8381[56] at 0x20092000 (0000:00:0a.0), 00:17:31:fb:e4:cd, IRQ 55, port TP.
Driver for NAND Flash on the PNX8550 XIO bus (Mar 15 2010-17:54:27)
Auto detected a >= 64MByte device on a 8 bit bus
NAND device: Manufacturer ID: 0xad, Chip ID: 0x76 (Hynix NAND 64MiB 3,3V 8-bit)
Scanning device for bad blocks
Creating 8 MTD partitions on "NAND 64MiB 3,3V 8-bit":
0x00000000-0x00004000 : "microBTM"
0x00004000-0x00084000 : "U-Boot"
0x00084000-0x0008c000 : "Env"
0x0008c000-0x00094000 : "bbt"
0x00094000-0x00894000 : "Linux"
0x00894000-0x03b94000 : "ROMFS"
0x03c00000-0x03ff8000 : "WinCE"
0x03ff8000-0x04000000 : "Info"
ehci_hcd 0000:00:09.2: EHCI Host Controller
ehci_hcd 0000:00:09.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:09.2: irq 55, io mem 0x20093200
ehci_hcd 0000:00:09.2: USB 2.0 started, EHCI 0.95, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
pnx8550-ohci pnx8550-ohci: PNX8550 OHCI
pnx8550-ohci pnx8550-ohci: new USB bus registered, assigned bus number 2
pnx8550-ohci pnx8550-ohci: irq 13, io mem 0x1be48000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd 0000:00:09.0: OHCI Host Controller
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:09.0: irq 55, io mem 0x20090000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ohci_hcd 0000:00:09.1: OHCI Host Controller
ohci_hcd 0000:00:09.1: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:09.1: irq 55, io mem 0x20091000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
USB Universal Host Controller Interface driver v3.0
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Bridge firewalling registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
eth0: DSPCFG accepted after 0 usec.
eth0: link up.
eth0: Setting full-duplex based on negotiated link capability.
Sending DHCP requests .<5>eth0: increased tx threshold, txcfg 0xd0f01004.
..... timed out!
IP-Config: Reopening network devices...
eth0: DSPCFG accepted after 0 usec.
eth0: link up.
eth0: Setting full-duplex based on negotiated link capability.
Sending DHCP requests .<5>eth0: increased tx threshold, txcfg 0xd0f01004.
., OK
IP-Config: Got DHCP answer from 192.168.1.1, my address is 192.168.1.171
IP-Config: Complete:
      device=eth0, addr=192.168.1.171, mask=255.255.255.0, gw=192.168.1.1,
    host=192.168.1.171, domain=lan, nis-domain=(none),
    bootserver=192.168.1.1, rootserver=192.168.1.1, rootpath=
Freeing unused kernel memory: 2044k freed
Algorithmics/MIPS FPU Emulator v1.5
Loading profile...  done
Mount fstab... done
Remount / read-write... done
Mounting new Root.
enabling SATA modules...sata_sil 0000:00:08.0: Applying R_ERR on DMA activate FIS errata fix
ata1: SATA max UDMA/100 cmd 0xc0058080 ctl 0xc005808a bmdma 0xc0058000 irq 55
ata2: SATA max UDMA/100 cmd 0xc00580c0 ctl 0xc00580ca bmdma 0xc0058008 irq 55
scsi0 : sata_sil
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: ATA-8: Hitachi HTS545050B9A300, PB4OC66G, max UDMA/133
ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/100
scsi1 : sata_sil
ata2: SATA link down (SStatus 0 SControl 310)
scsi 0:0:0:0: Direct-Access    ATA      Hitachi HTS54505 PB4O PQ: 0 ANSI: 5
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
sda: Write Protect is off
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
sda: Write Protect is off
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3
sd 0:0:0:0: Attached scsi disk sda
done
Creating device nodes...done
Setup mdev as hotplug handler... done
Set log level...
Populate /dev... Load luddite and gpio/mmio/rtc...Get display mode and load i2c and fb modules... Detect GPIO function...done
Get System ID...
Restore hotplug handler... done
Restore log level...
Unloading modules...
CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == 801f30dc, ra == c00729e4
Oops[#1]:
Cpu 0
$ 0  : 00000000 10008401 00100100 00000000
$ 4  : 00000000 00000000 c0064304 86e39ed8
$ 8  : 803896b0 86e39ee1 800a86a8 0000000c
$12  : 43545262 2aab2800 00000000 2aab2800
$16  : c0072e80 c0072e74 00000087 00000480
$20  : 00000000 00000002 00000000 00000003
$24  : 00000000 2acec13c
$28  : 86e38000 86e39e80 7ffc3c20 c00729e4
Hi    : 00000372
Lo    : 0002c316
epc  : 801f30dc    Tainted: P
ra    : c00729e4 Status: 10008403    KERNEL EXL IE
Cause : 1080000c
BadVA : 00000000
PrId  : 00061200
Modules linked in: sysid(P) i2c_algo_IP0105 i2c_algo_IP3203 phStbRTC phStbMmio phStbGpio phStbProc lud_pnx8550 lud_core sata_sil libata
Process exe (pid: 312, threadinfo=86e38000, task=81116000)
Stack : 805b0000 805b0000 0000004f 00030002 80390000 c0072f20 80390000 c00729e4
        805b4e50 80099104 8008dfc0 00000000 800a8844 800a86d4 805b4e50 8008a36c
        86e39ec0 86e39ec0 00000000 c0072f20 00000480 86e39ec8 74536870 43545262
        00000000 00000012 10008400 00000201 004035fc 2aabdd08 10008400 8008a540
        00000000 80096090 7ffc3de1 00000001 00fc3d08 00000480 7ffc3de1 00000001
        ...
Call Trace:[<c00729e4>][<80099104>][<8008dfc0>][<800a8844>][<800a86d4>][<8008a36c>][<8008a540>][<80096090>][<80069f00>][<80061d80>]
Code: 8e030000  3c020010  34420100 <ac830000> ae020000  3c020020  34420200  ac640004  ae020004
Shutting down PNX8550 MMIO Driver
Shutting down PNX8550 GPIO driver
Shutting down NXP /proc entries driver
done
done
Mount nfs root /dev/sda1... kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
done
Switch root
INIT: version 2.86 booting
.udev/ already exists on the static /dev! (warning).
Starting the hotplug events dispatcher: udevdudevd[425]: main: the kernel does not support inotify, udevd can't monitor rules file changes
.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...udevd-event[496]: rename_netif: error changing netif name eth0 to eth1: Device or resource busy
Registering SPI driver
Register ProSLIC driver
à
U-Boot 2011.09-00000-gf54ce7f-dirty (Dec 20 2011 - 12:36:29)
DRAM:  128 MiB
NAND:  NAND device: Manufacturer ID: 0xad, Chip ID: 0x76 (Hynix NAND 64MiB 3,3V 8-bit)
64 MiB
Bad block table at page 1120, version 0x01
Bad block table at page 1152, version 0x01
In:    serial
Out:  serial
Err:  serial
Net:  natsemi: EEPROM contents:
d008 0400 0b34 00f3 0000 0000 0000 8b80 7d98 66f2 0000 aae2
natsemi: MAC-Address: 0:17:31:FB:E4:CD
dp83815#0
Welcome to the pollinux board v1.1
Hit any key to stop autoboot:  0
Loading from nand0, offset 0x94000
  Image Name:  Elecard Linux 2.6
  Created:      2011-12-07  16:01:46 UTC
  Image Type:  MIPS Elecard Linux Kernel Image (gzip compressed)
  Data Size:    3233500 Bytes = 3.1 MiB
  Load Address: 80060000
  Entry Point:  803a9000
** Too many args (max. 16) **
** Too many args (max. 16) **
## Booting kernel from Legacy Image at 82000000 ...
  Image Name:  Elecard Linux 2.6
  Created:      2011-12-07  16:01:46 UTC
  Image Type:  MIPS Elecard Linux Kernel Image (gzip compressed)
  Data Size:    3233500 Bytes = 3.1 MiB
  Load Address: 80060000
  Entry Point:  803a9000
  Verifying Checksum ... OK
  Uncompressing Kernel Image ... OK
Starting kernel ...
Determined physical RAM map:
memory: 07000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Built 1 zonelists.  Total pages: 28448
Kernel command line: console=ttyS1,38400n8 stb810_display=pal nomainapp=1 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw
Primary instruction cache 16kB, physically tagged, 2-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (23 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 512 (order: 9, 2048 bytes)
Using 250.714 MHz high precision timer.
Linux version 2.6.21.3PNX8550 (root@smithy) (gcc version 4.0.0 (DENX ELDK 4.0 4.0.0)) #1743 Fri Feb 11 10:49:15 OMST 2011
Setting initial splash screen display mode SD (50Hz)
CPU revision is: 00061200
Determined physical RAM map:
memory: 07000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Built 1 zonelists.  Total pages: 28448
Kernel command line: console=ttyS1,38400n8 stb810_display=pal nomainapp=1 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw
Primary instruction cache 16kB, physically tagged, 2-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (23 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 512 (order: 9, 2048 bytes)
Using 250.714 MHz high precision timer.
Console: colour dummy device 80x25
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 107648k/114688k available (2841k kernel code, 6996k reserved, 518k data, 2044k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Time: MIPS clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NTFS driver 2.1.28 [Flags: R/O].
JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler anticipatory registered (default)
Register GPIO SPI device
Serial: PNX8XXX driver $Revision: 1.2 $
pnx8xxx-uart: ttyS0 at MMIO 0xbbe4a000 (irq = 27) is a PNX8XXX
pnx8xxx-uart: ttyS1 at MMIO 0xbbe4b000 (irq = 28) is a PNX8XXX
natsemi dp8381x driver, version 2.1, Sept 11, 2006
  originally by Donald Becker <becker@scyld.com>
  http://www.scyld.com/network/natsemi.html
  2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
PCI: Enabling device 0000:00:0a.0 (0006 -> 0007)
natsemi eth0: NatSemi DP8381[56] at 0x20092000 (0000:00:0a.0), 00:17:31:fb:e4:cd, IRQ 55, port TP.
Driver for NAND Flash on the PNX8550 XIO bus (Mar 15 2010-17:54:27)
Auto detected a >= 64MByte device on a 8 bit bus
NAND device: Manufacturer ID: 0xad, Chip ID: 0x76 (Hynix NAND 64MiB 3,3V 8-bit)
Scanning device for bad blocks
Creating 8 MTD partitions on "NAND 64MiB 3,3V 8-bit":
0x00000000-0x00004000 : "microBTM"
0x00004000-0x00084000 : "U-Boot"
0x00084000-0x0008c000 : "Env"
0x0008c000-0x00094000 : "bbt"
0x00094000-0x00894000 : "Linux"
0x00894000-0x03b94000 : "ROMFS"
0x03c00000-0x03ff8000 : "WinCE"
0x03ff8000-0x04000000 : "Info"
ehci_hcd 0000:00:09.2: EHCI Host Controller
ehci_hcd 0000:00:09.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:09.2: irq 55, io mem 0x20093200
ehci_hcd 0000:00:09.2: USB 2.0 started, EHCI 0.95, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
pnx8550-ohci pnx8550-ohci: PNX8550 OHCI
pnx8550-ohci pnx8550-ohci: new USB bus registered, assigned bus number 2
pnx8550-ohci pnx8550-ohci: irq 13, io mem 0x1be48000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd 0000:00:09.0: OHCI Host Controller
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:09.0: irq 55, io mem 0x20090000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ohci_hcd 0000:00:09.1: OHCI Host Controller
ohci_hcd 0000:00:09.1: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:09.1: irq 55, io mem 0x20091000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
USB Universal Host Controller Interface driver v3.0
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Bridge firewalling registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
eth0: DSPCFG accepted after 0 usec.
eth0: link up.
eth0: Setting full-duplex based on negotiated link capability.
Sending DHCP requests .<5>eth0: increased tx threshold, txcfg 0xd0f01004.
..... timed out!
IP-Config: Reopening network devices...
eth0: DSPCFG accepted after 0 usec.
eth0: link up.
eth0: Setting full-duplex based on negotiated link capability.
Sending DHCP requests .<5>eth0: increased tx threshold, txcfg 0xd0f01004.
., OK
IP-Config: Got DHCP answer from 192.168.1.1, my address is 192.168.1.171
IP-Config: Complete:
      device=eth0, addr=192.168.1.171, mask=255.255.255.0, gw=192.168.1.1,
    host=192.168.1.171, domain=lan, nis-domain=(none),
    bootserver=192.168.1.1, rootserver=192.168.1.1, rootpath=
Freeing unused kernel memory: 2044k freed
Algorithmics/MIPS FPU Emulator v1.5
Loading profile...  done
Mount fstab... done
Remount / read-write... done
Mounting new Root.
enabling SATA modules...sata_sil 0000:00:08.0: Applying R_ERR on DMA activate FIS errata fix
ata1: SATA max UDMA/100 cmd 0xc0058080 ctl 0xc005808a bmdma 0xc0058000 irq 55
ata2: SATA max UDMA/100 cmd 0xc00580c0 ctl 0xc00580ca bmdma 0xc0058008 irq 55
scsi0 : sata_sil
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: ATA-8: Hitachi HTS545050B9A300, PB4OC66G, max UDMA/133
ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/100
scsi1 : sata_sil
ata2: SATA link down (SStatus 0 SControl 310)
scsi 0:0:0:0: Direct-Access    ATA      Hitachi HTS54505 PB4O PQ: 0 ANSI: 5
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
sda: Write Protect is off
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
sda: Write Protect is off
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3
sd 0:0:0:0: Attached scsi disk sda
done
Creating device nodes...done
Setup mdev as hotplug handler... done
Set log level...
Populate /dev... Load luddite and gpio/mmio/rtc...Get display mode and load i2c and fb modules... Detect GPIO function...done
Get System ID...
Restore hotplug handler... done
Restore log level...
Unloading modules...
CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == 801f30dc, ra == c00729e4
Oops[#1]:
Cpu 0
$ 0  : 00000000 10008401 00100100 00000000
$ 4  : 00000000 00000000 c0064304 86e39ed8
$ 8  : 803896b0 86e39ee1 800a86a8 0000000c
$12  : 43545262 2aab2800 00000000 2aab2800
$16  : c0072e80 c0072e74 00000087 00000480
$20  : 00000000 00000002 00000000 00000003
$24  : 00000000 2acec13c
$28  : 86e38000 86e39e80 7fd49c20 c00729e4
Hi    : 00000372
Lo    : 0002c316
epc  : 801f30dc    Tainted: P
ra    : c00729e4 Status: 10008403    KERNEL EXL IE
Cause : 1080000c
BadVA : 00000000
PrId  : 00061200
Modules linked in: sysid(P) i2c_algo_IP0105 i2c_algo_IP3203 phStbRTC phStbMmio phStbGpio phStbProc lud_pnx8550 lud_core sata_sil libata
Process exe (pid: 312, threadinfo=86e38000, task=811027f0)
Stack : 805b0000 805b0000 0000004f 00030002 80390000 c0072f20 80390000 c00729e4
        805b4e50 80099104 8008dfc0 0002ad9b 800a8844 800a86d4 805b4e50 8008a36c
        86e39ec0 86e39ec0 00000000 c0072f20 00000480 86e39ec8 74536870 43545262
        00000000 00000001 10008400 2aafdcb8 00000000 00000000 10008400 8008a540
        00000000 80096090 7fd49de1 00000001 00d49d08 00000480 7fd49de1 00000001
        ...
Call Trace:[<c00729e4>][<80099104>][<8008dfc0>][<800a8844>][<800a86d4>][<8008a36c>][<8008a540>][<80096090>][<80069f00>][<80061d80>]
Code: 8e030000  3c020010  34420100 <ac830000> ae020000  3c020020  34420200  ac640004  ae020004
Shutting down PNX8550 MMIO Driver
Shutting down PNX8550 GPIO driver
Shutting down NXP /proc entries driver
done
done
Mount nfs root /dev/sda1... kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on sda1, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
done
Switch root
INIT: version 2.86 booting
.udev/ already exists on the static /dev! (warning).
Starting the hotplug events dispatcher: udevdudevd[425]: main: the kernel does not support inotify, udevd can't monitor rules file changes
.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...udevd-event[493]: rename_netif: error changing netif name eth0 to eth1: Device or resource busy
Registering SPI driver
Register ProSLIC driver
U-Boot 2011.09-00000-gf54ce7f-dirty (Dec 20 2011 - 12:36:29)
DRAM:  128 MiB
NAND:  NAND device: Manufacturer ID: 0xad, Chip ID: 0x76 (Hynix NAND 64MiB 3,3V 8-bit)
64 MiB
Bad block table at page 1120, version 0x01
Bad block table at page 1152, version 0x01
In:    serial
Out:  serial
Err:  serial
Net:  natsemi: EEPROM contents:
d008 0400 0b34 00f3 0000 0000 0000 8b80 7d98 66f2 0000 aae2
natsemi: MAC-Address: 0:17:31:FB:E4:CD
dp83815#0
Welcome to the pollinux board v1.1
Hit any key to stop autoboot:  1 à
U-Boot 2011.09-00000-gf54ce7f-dirty (Dec 20 2011 - 12:36:29)
DRAM:  128 MiB
NAND:  NAND device: Manufacturer ID: 0xad, Chip ID: 0x76 (Hynix NAND 64MiB 3,3V 8-bit)
64 MiB
Bad block table at page 1120, version 0x01
Bad block table at page 1152, version 0x01
In:    serial
Out:  serial
Err:  serial
Net:  natsemi: EEPROM contents:
d008 0400 0b34 00f3 0000 0000 0000 8b80 7d98 66f2 0000 aae2
natsemi: MAC-Address: 0:17:31:FB:E4:CD
dp83815#0
Welcome to the pollinux board v1.1
Hit any key to stop autoboot:  0
Loading from nand0, offset 0x94000
  Image Name:  Elecard Linux 2.6
  Created:      2011-12-07  16:01:46 UTC
  Image Type:  MIPS Elecard Linux Kernel Image (gzip compressed)
  Data Size:    3233500 Bytes = 3.1 MiB
  Load Address: 80060000
  Entry Point:  803a9000
** Too many args (max. 16) **
** Too many args (max. 16) **
## Booting kernel from Legacy Image at 82000000 ...
  Image Name:  Elecard Linux 2.6
  Created:      2011-12-07  16:01:46 UTC
  Image Type:  MIPS Elecard Linux Kernel Image (gzip compressed)
  Data Size:    3233500 Bytes = 3.1 MiB
  Load Address: 80060000
  Entry Point:  803a9000
  Verifying Checksum ... OK
  Uncompressing Kernel Image ... OK
Starting kernel ...
Determined physical RAM map:
memory: 07000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Built 1 zonelists.  Total pages: 28448
Kernel command line: console=ttyS1,38400n8 stb810_display=pal nomainapp=1 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw
Primary instruction cache 16kB, physically tagged, 2-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (23 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 512 (order: 9, 2048 bytes)
Using 250.714 MHz high precision timer.
Linux version 2.6.21.3PNX8550 (root@smithy) (gcc version 4.0.0 (DENX ELDK 4.0 4.0.0)) #1743 Fri Feb 11 10:49:15 OMST 2011
Setting initial splash screen display mode SD (50Hz)
CPU revision is: 00061200
Determined physical RAM map:
memory: 07000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Built 1 zonelists.  Total pages: 28448
Kernel command line: console=ttyS1,38400n8 stb810_display=pal nomainapp=1 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw
Primary instruction cache 16kB, physically tagged, 2-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (23 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 512 (order: 9, 2048 bytes)
Using 250.714 MHz high precision timer.
Console: colour dummy device 80x25
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 107648k/114688k available (2841k kernel code, 6996k reserved, 518k data, 2044k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Time: MIPS clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NTFS driver 2.1.28 [Flags: R/O].
JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler anticipatory registered (default)
Register GPIO SPI device
Serial: PNX8XXX driver $Revision: 1.2 $
pnx8xxx-uart: ttyS0 at MMIO 0xbbe4a000 (irq = 27) is a PNX8XXX
pnx8xxx-uart: ttyS1 at MMIO 0xbbe4b000 (irq = 28) is a PNX8XXX
natsemi dp8381x driver, version 2.1, Sept 11, 2006
  originally by Donald Becker <becker@scyld.com>
  http://www.scyld.com/network/natsemi.html
  2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
PCI: Enabling device 0000:00:0a.0 (0006 -> 0007)
natsemi eth0: NatSemi DP8381[56] at 0x20092000 (0000:00:0a.0), 00:17:31:fb:e4:cd, IRQ 55, port TP.
Driver for NAND Flash on the PNX8550 XIO bus (Mar 15 2010-17:54:27)
Auto detected a >= 64MByte device on a 8 bit bus
NAND device: Manufacturer ID: 0xad, Chip ID: 0x76 (Hynix NAND 64MiB 3,3V 8-bit)
Scanning device for bad blocks
Creating 8 MTD partitions on "NAND 64MiB 3,3V 8-bit":
0x00000000-0x00004000 : "microBTM"
0x00004000-0x00084000 : "U-Boot"
0x00084000-0x0008c000 : "Env"
0x0008c000-0x00094000 : "bbt"
0x00094000-0x00894000 : "Linux"
0x00894000-0x03b94000 : "ROMFS"
0x03c00000-0x03ff8000 : "WinCE"
0x03ff8000-0x04000000 : "Info"
ehci_hcd 0000:00:09.2: EHCI Host Controller
ehci_hcd 0000:00:09.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:09.2: irq 55, io mem 0x20093200
ehci_hcd 0000:00:09.2: USB 2.0 started, EHCI 0.95, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
pnx8550-ohci pnx8550-ohci: PNX8550 OHCI
pnx8550-ohci pnx8550-ohci: new USB bus registered, assigned bus number 2
pnx8550-ohci pnx8550-ohci: irq 13, io mem 0x1be48000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd 0000:00:09.0: OHCI Host Controller
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:09.0: irq 55, io mem 0x20090000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ohci_hcd 0000:00:09.1: OHCI Host Controller
ohci_hcd 0000:00:09.1: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:09.1: irq 55, io mem 0x20091000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
USB Universal Host Controller Interface driver v3.0
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Bridge firewalling registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
eth0: DSPCFG accepted after 0 usec.
eth0: link up.
eth0: Setting full-duplex based on negotiated link capability.
Sending DHCP requests .<5>eth0: increased tx threshold, txcfg 0xd0f01004.
..... timed out!
IP-Config: Reopening network devices...
eth0: DSPCFG accepted after 0 usec.
eth0: link up.
eth0: Setting full-duplex based on negotiated link capability.
Sending DHCP requests .<5>eth0: increased tx threshold, txcfg 0xd0f01004.
., OK
IP-Config: Got DHCP answer from 192.168.1.1, my address is 192.168.1.171
IP-Config: Complete:
      device=eth0, addr=192.168.1.171, mask=255.255.255.0, gw=192.168.1.1,
    host=192.168.1.171, domain=lan, nis-domain=(none),
    bootserver=192.168.1.1, rootserver=192.168.1.1, rootpath=
Freeing unused kernel memory: 2044k freed
Algorithmics/MIPS FPU Emulator v1.5
Loading profile...  done
Mount fstab... done
Remount / read-write... done
Mounting new Root.
enabling SATA modules...sata_sil 0000:00:08.0: Applying R_ERR on DMA activate FIS errata fix
ata1: SATA max UDMA/100 cmd 0xc0058080 ctl 0xc005808a bmdma 0xc0058000 irq 55
ata2: SATA max UDMA/100 cmd 0xc00580c0 ctl 0xc00580ca bmdma 0xc0058008 irq 55
scsi0 : sata_sil
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: ATA-8: Hitachi HTS545050B9A300, PB4OC66G, max UDMA/133
ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/100
scsi1 : sata_sil
ata2: SATA link down (SStatus 0 SControl 310)
scsi 0:0:0:0: Direct-Access    ATA      Hitachi HTS54505 PB4O PQ: 0 ANSI: 5
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
sda: Write Protect is off
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
sda: Write Protect is off
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3
sd 0:0:0:0: Attached scsi disk sda
done
Creating device nodes...done
Setup mdev as hotplug handler... done
Set log level...
Populate /dev... Load luddite and gpio/mmio/rtc...Get display mode and load i2c and fb modules... Detect GPIO function...done
Get System ID...
Restore hotplug handler... done
Restore log level...
Unloading modules...
CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == 801f30dc, ra == c00729e4
Oops[#1]:
Cpu 0
$ 0  : 00000000 10008401 00100100 00000000
$ 4  : 00000000 00000000 c0064304 86e3bed8
$ 8  : 803896b0 86e3bee1 800a86a8 0000000c
$12  : 43545262 2aab2800 00000000 2aab2800
$16  : c0072e80 c0072e74 00000087 00000480
$20  : 00000000 00000002 00000000 00000003
$24  : 00000000 2acec13c
$28  : 86e3a000 86e3be80 7f887c20 c00729e4
Hi    : 00000372
Lo    : 0002c316
epc  : 801f30dc    Tainted: P
ra    : c00729e4 Status: 10008403    KERNEL EXL IE
Cause : 1080000c
BadVA : 00000000
PrId  : 00061200
Modules linked in: sysid(P) i2c_algo_IP0105 i2c_algo_IP3203 phStbRTC phStbMmio phStbGpio phStbProc lud_pnx8550 lud_core sata_sil libata
Process exe (pid: 312, threadinfo=86e3a000, task=81119be8)
Stack : 805b0000 805b0000 0000004f 00030002 80390000 c0072f20 80390000 c00729e4
        805b4e50 80099104 8008dfc0 0002ad9b 800a8844 800a86d4 805b4e50 8008a36c
        86e3bec0 86e3bec0 00000000 c0072f20 00000480 86e3bec8 74536870 43545262
        00000000 00000001 10008400 0f565c6e 00000000 2aabdd08 10008400 8008a540
        00000000 80096090 7f887de1 00000001 00887d08 00000480 7f887de1 00000001
        ...
Call Trace:[<c00729e4>][<80099104>][<8008dfc0>][<800a8844>][<800a86d4>][<8008a36c>][<8008a540>][<80096090>][<80069f00>][<80061d80>]
Code: 8e030000  3c020010  34420100 <ac830000> ae020000  3c020020  34420200  ac640004  ae020004
Shutting down PNX8550 MMIO Driver
Shutting down PNX8550 GPIO driver
Shutting down NXP /proc entries driver
done
done
Mount nfs root /dev/sda1... kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on sda1, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
done
Switch root
INIT: version 2.86 booting
.udev/ already exists on the static /dev! (warning).
Starting the hotplug events dispatcher: udevdudevd[425]: main: the kernel does not support inotify, udevd can't monitor rules file changes
.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...udevd-event[495]: rename_netif: error changing netif name eth0 to eth1: Device or resource busy
Registering SPI driver
Register ProSLIC driver
U-Boot 2011.09-00000-gf54ce7f-dirty (Dec 20 2011 - 12:36:29)
DRAM:  128 MiB
NAND:  NAND device: Manufacturer ID: 0xad, Chip ID: 0x76 (Hynix NAND 64MiB 3,3V 8-bit)
64 MiB
Bad block table at page 1120, version 0x01
Bad block table at page 1152, version 0x01
In:    serial
Out:  serial
Err:  serial
Net:  natsemi: EEPROM contents:
d008 0400 0b34 00f3 0000 0000 0000 8b80 7d98 66f2 0000 aae2
natsemi: MAC-Address: 0:17:31:FB:E4:CD
dp83815#0
Welcome to the pollinux board v1.1
Hit any key to stop autoboot:  0
Loading from nand0, offset 0x94000
  Image Name:  Elecard Linux 2.6
  Created:      2011-12-07  16:01:46 UTC
  Image Type:  MIPS Elecard Linux Kernel Image (gzip compressed)
  Data Size:    3233500 Bytes = 3.1 MiB
  Load Address: 80060000
  Entry Point:  803a9000
** Too many args (max. 16) **
** Too many args (max. 16) **
## Booting kernel from Legacy Image at 82000000 ...
  Image Name:  Elecard Linux 2.6
  Created:      2011-12-07  16:01:46 UTC
  Image Type:  MIPS Elecard Linux Kernel Image (gzip compressed)
  Data Size:    3233500 Bytes = 3.1 MiB
  Load Address: 80060000
  Entry Point:  803a9000
  Verifying Checksum ... OK
  Uncompressing Kernel Image ... OK
Starting kernel ...
Determined physical RAM map:
memory: 07000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Built 1 zonelists.  Total pages: 28448
Kernel command line: console=ttyS1,38400n8 stb810_display=pal nomainapp=1 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw
Primary instruction cache 16kB, physically tagged, 2-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (23 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 512 (order: 9, 2048 bytes)
Using 250.714 MHz high precision timer.
Linux version 2.6.21.3PNX8550 (root@smithy) (gcc version 4.0.0 (DENX ELDK 4.0 4.0.0)) #1743 Fri Feb 11 10:49:15 OMST 2011
Setting initial splash screen display mode SD (50Hz)
CPU revision is: 00061200
Determined physical RAM map:
memory: 07000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Built 1 zonelists.  Total pages: 28448
Kernel command line: console=ttyS1,38400n8 stb810_display=pal nomainapp=1 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw
Primary instruction cache 16kB, physically tagged, 2-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (23 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 512 (order: 9, 2048 bytes)
Using 250.714 MHz high precision timer.
Console: colour dummy device 80x25
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 107648k/114688k available (2841k kernel code, 6996k reserved, 518k data, 2044k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Time: MIPS clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NTFS driver 2.1.28 [Flags: R/O].
JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler anticipatory registered (default)
Register GPIO SPI device
Serial: PNX8XXX driver $Revision: 1.2 $
pnx8xxx-uart: ttyS0 at MMIO 0xbbe4a000 (irq = 27) is a PNX8XXX
pnx8xxx-uart: ttyS1 at MMIO 0xbbe4b000 (irq = 28) is a PNX8XXX
natsemi dp8381x driver, version 2.1, Sept 11, 2006
  originally by Donald Becker <becker@scyld.com>
  http://www.scyld.com/network/natsemi.html
  2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
PCI: Enabling device 0000:00:0a.0 (0006 -> 0007)
natsemi eth0: NatSemi DP8381[56] at 0x20092000 (0000:00:0a.0), 00:17:31:fb:e4:cd, IRQ 55, port TP.
Driver for NAND Flash on the PNX8550 XIO bus (Mar 15 2010-17:54:27)
Auto detected a >= 64MByte device on a 8 bit bus
NAND device: Manufacturer ID: 0xad, Chip ID: 0x76 (Hynix NAND 64MiB 3,3V 8-bit)
Scanning device for bad blocks
Creating 8 MTD partitions on "NAND 64MiB 3,3V 8-bit":
0x00000000-0x00004000 : "microBTM"
0x00004000-0x00084000 : "U-Boot"
0x00084000-0x0008c000 : "Env"
0x0008c000-0x00094000 : "bbt"
0x00094000-0x00894000 : "Linux"
0x00894000-0x03b94000 : "ROMFS"
0x03c00000-0x03ff8000 : "WinCE"
0x03ff8000-0x04000000 : "Info"
ehci_hcd 0000:00:09.2: EHCI Host Controller
ehci_hcd 0000:00:09.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:09.2: irq 55, io mem 0x20093200
ehci_hcd 0000:00:09.2: USB 2.0 started, EHCI 0.95, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
pnx8550-ohci pnx8550-ohci: PNX8550 OHCI
pnx8550-ohci pnx8550-ohci: new USB bus registered, assigned bus number 2
pnx8550-ohci pnx8550-ohci: irq 13, io mem 0x1be48000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd 0000:00:09.0: OHCI Host Controller
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:09.0: irq 55, io mem 0x20090000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ohci_hcd 0000:00:09.1: OHCI Host Controller
ohci_hcd 0000:00:09.1: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:09.1: irq 55, io mem 0x20091000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
USB Universal Host Controller Interface driver v3.0
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Bridge firewalling registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
eth0: DSPCFG accepted after 0 usec.
eth0: link up.
eth0: Setting full-duplex based on negotiated link capability.
Sending DHCP requests .<5>eth0: increased tx threshold, txcfg 0xd0f01004.
..... timed out!
IP-Config: Reopening network devices...
eth0: DSPCFG accepted after 0 usec.
eth0: link up.
eth0: Setting full-duplex based on negotiated link capability.
Sending DHCP requests .<5>eth0: increased tx threshold, txcfg 0xd0f01004.
., OK
IP-Config: Got DHCP answer from 192.168.1.1, my address is 192.168.1.171
IP-Config: Complete:
      device=eth0, addr=192.168.1.171, mask=255.255.255.0, gw=192.168.1.1,
    host=192.168.1.171, domain=lan, nis-domain=(none),
    bootserver=192.168.1.1, rootserver=192.168.1.1, rootpath=
Freeing unused kernel memory: 2044k freed
Algorithmics/MIPS FPU Emulator v1.5
Loading profile...  done
Mount fstab... done
Remount / read-write... done
Mounting new Root.
enabling SATA modules...sata_sil 0000:00:08.0: Applying R_ERR on DMA activate FIS errata fix
ata1: SATA max UDMA/100 cmd 0xc0058080 ctl 0xc005808a bmdma 0xc0058000 irq 55
ata2: SATA max UDMA/100 cmd 0xc00580c0 ctl 0xc00580ca bmdma 0xc0058008 irq 55
scsi0 : sata_sil
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: ATA-8: Hitachi HTS545050B9A300, PB4OC66G, max UDMA/133
ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/100
scsi1 : sata_sil
ata2: SATA link down (SStatus 0 SControl 310)
scsi 0:0:0:0: Direct-Access    ATA      Hitachi HTS54505 PB4O PQ: 0 ANSI: 5
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
sda: Write Protect is off
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
sda: Write Protect is off
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3
sd 0:0:0:0: Attached scsi disk sda
done
Creating device nodes...done
Setup mdev as hotplug handler... done
Set log level...
Populate /dev... Load luddite and gpio/mmio/rtc...Get display mode and load i2c and fb modules... Detect GPIO function...done
Get System ID...
Restore hotplug handler... done
Restore log level...
Unloading modules...
CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == 801f30dc, ra == c00729e4
Oops[#1]:
Cpu 0
$ 0  : 00000000 10008401 00100100 00000000
$ 4  : 00000000 00000000 c0064304 86e39ed8
$ 8  : 803896b0 86e39ee1 800a86a8 0000000c
$12  : 43545262 2aab2800 00000000 2aab2800
$16  : c0072e80 c0072e74 00000087 00000480
$20  : 00000000 00000002 00000000 00000003
$24  : 00000000 2acec13c
$28  : 86e38000 86e39e80 7fc64c20 c00729e4
Hi    : 00000372
Lo    : 0002c316
epc  : 801f30dc    Tainted: P
ra    : c00729e4 Status: 10008403    KERNEL EXL IE
Cause : 1080000c
BadVA : 00000000
PrId  : 00061200
Modules linked in: sysid(P) i2c_algo_IP0105 i2c_algo_IP3203 phStbRTC phStbMmio phStbGpio phStbProc lud_pnx8550 lud_core sata_sil libata
Process exe (pid: 312, threadinfo=86e38000, task=811027f0)
Stack : 00000003 80098f84 0000004f 00030002 80390000 c0072f20 80390000 c00729e4
        805b4e50 80099104 8008dfc0 0002ad9b 800a8844 800a86d4 805b4e50 8008a36c
        86e39ec0 86e39ec0 00000000 c0072f20 00000480 86e39ec8 74536870 43545262
        00000200 00000001 10008400 10002eb8 2aafdcb8 004068d0 10008400 8008a540
        00000000 80096090 7fc64de1 00000001 00c64d08 00000480 7fc64de1 00000001
        ...
Call Trace:[<80098f84>][<c00729e4>][<80099104>][<8008dfc0>][<800a8844>][<800a86d4>][<8008a36c>][<8008a540>][<80096090>][<80069f00>][<80061d80>]
Code: 8e030000  3c020010  34420100 <ac830000> ae020000  3c020020  34420200  ac640004  ae020004
Shutting down PNX8550 MMIO Driver
Shutting down PNX8550 GPIO driver
Shutting down NXP /proc entries driver
done
done
Mount nfs root /dev/sda1... kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on sda1, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
done
Switch root
INIT: version 2.86 booting
.udev/ already exists on the static /dev! (warning).
Starting the hotplug events dispatcher: udevdudevd[425]: main: the kernel does not support inotify, udevd can't monitor rules file changes
.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...udevd-event[494]: rename_netif: error changing netif name eth0 to eth1: Device or resource busy
Registering SPI driver
Register ProSLIC driver
Setting parameters of disc: (none).
Setting the system clock.
Cannot access the Hardware Clock via any known method.
Use the --debug option to see the details of our search for an access method.
Unable to set System Clock to: Sat Jan 1 00:01:40 UTC 2000 (warning).
Activating swap...done.
Setting the system clock.
Cannot access the Hardware Clock via any known method.
Use the --debug option to see the details of our search for an access method.
Unable to set System Clock to: Sat Jan 1 00:01:41 UTC 2000 (warning).
Cleaning up ifupdown....
Loading kernel modules...done.
Checking file systems...fsck 1.41.3 (12-Oct-2008)
done.
Setting kernel variables (/etc/sysctl.conf)...done.
Mounting local filesystems...kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on sda2, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda3, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
done.
Activating swapfile swap...done.
Setting up networking....
Configuring network interfaces...done.
Luddite version 3, exported  Mon Apr 25 10:40:08 BST 2005
TM0: detected clock 270000000
lud_core: Registering devfs device 0/lud
TM1: detected clock 270000000
lud_core: Registering devfs device 1/lud
NXP /proc entries driver (Aug 13 2007-11:59:40)
dspinfo: Initialising DSP Info Driver
PNX8550 MMIO Driver (Aug 13 2007-11:59:38)
dspmem: Initialising DSP memory Driver
U-Boot 2011.09-00000-gf54ce7f-dirty (Dec 20 2011 - 12:36:29)
DRAM:  128 MiB
NAND:  NAND device: Manufacturer ID: 0xad, Chip ID: 0x76 (Hynix NAND 64MiB 3,3V 8-bit)
64 MiB
Bad block table at page 1120, version 0x01
Bad block table at page 1152, version 0x01
In:    serial
Out:  serial
Err:  serial
Net:  natsemi: EEPROM contents:
d008 0400 0b34 00f3 0000 0000 0000 8b80 7d98 66f2 0000 aae2
natsemi: MAC-Address: 0:17:31:FB:E4:CD
dp83815#0
Welcome to the pollinux board v1.1
Hit any key to stop autoboot:  0
Loading from nand0, offset 0x94000
  Image Name:  Elecard Linux 2.6
  Created:      2011-12-07  16:01:46 UTC
  Image Type:  MIPS Elecard Linux Kernel Image (gzip compressed)
  Data Size:    3233500 Bytes = 3.1 MiB
  Load Address: 80060000
  Entry Point:  803a9000
** Too many args (max. 16) **
** Too many args (max. 16) **
## Booting kernel from Legacy Image at 82000000 ...
  Image Name:  Elecard Linux 2.6
  Created:      2011-12-07  16:01:46 UTC
  Image Type:  MIPS Elecard Linux Kernel Image (gzip compressed)
  Data Size:    3233500 Bytes = 3.1 MiB
  Load Address: 80060000
  Entry Point:  803a9000
  Verifying Checksum ... OK
  Uncompressing Kernel Image ... OK
Starting kernel ...
Determined physical RAM map:
memory: 07000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Built 1 zonelists.  Total pages: 28448
Kernel command line: console=ttyS1,38400n8 stb810_display=pal nomainapp=1 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw
Primary instruction cache 16kB, physically tagged, 2-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (23 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 512 (order: 9, 2048 bytes)
Using 250.714 MHz high precision timer.
Linux version 2.6.21.3PNX8550 (root@smithy) (gcc version 4.0.0 (DENX ELDK 4.0 4.0.0)) #1743 Fri Feb 11 10:49:15 OMST 2011
Setting initial splash screen display mode SD (50Hz)
CPU revision is: 00061200
Determined physical RAM map:
memory: 07000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Built 1 zonelists.  Total pages: 28448
Kernel command line: console=ttyS1,38400n8 stb810_display=pal nomainapp=1 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw
Primary instruction cache 16kB, physically tagged, 2-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (23 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 512 (order: 9, 2048 bytes)
Using 250.714 MHz high precision timer.
Console: colour dummy device 80x25
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 107648k/114688k available (2841k kernel code, 6996k reserved, 518k data, 2044k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Time: MIPS clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NTFS driver 2.1.28 [Flags: R/O].
JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler anticipatory registered (default)
Register GPIO SPI device
Serial: PNX8XXX driver $Revision: 1.2 $
pnx8xxx-uart: ttyS0 at MMIO 0xbbe4a000 (irq = 27) is a PNX8XXX
pnx8xxx-uart: ttyS1 at MMIO 0xbbe4b000 (irq = 28) is a PNX8XXX
natsemi dp8381x driver, version 2.1, Sept 11, 2006
  originally by Donald Becker <becker@scyld.com>
  http://www.scyld.com/network/natsemi.html
  2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
PCI: Enabling device 0000:00:0a.0 (0006 -> 0007)
natsemi eth0: NatSemi DP8381[56] at 0x20092000 (0000:00:0a.0), 00:17:31:fb:e4:cd, IRQ 55, port TP.
Driver for NAND Flash on the PNX8550 XIO bus (Mar 15 2010-17:54:27)
Auto detected a >= 64MByte device on a 8 bit bus
NAND device: Manufacturer ID: 0xad, Chip ID: 0x76 (Hynix NAND 64MiB 3,3V 8-bit)
Scanning device for bad blocks
Creating 8 MTD partitions on "NAND 64MiB 3,3V 8-bit":
0x00000000-0x00004000 : "microBTM"
0x00004000-0x00084000 : "U-Boot"
0x00084000-0x0008c000 : "Env"
0x0008c000-0x00094000 : "bbt"
0x00094000-0x00894000 : "Linux"
0x00894000-0x03b94000 : "ROMFS"
0x03c00000-0x03ff8000 : "WinCE"
0x03ff8000-0x04000000 : "Info"
ehci_hcd 0000:00:09.2: EHCI Host Controller
ehci_hcd 0000:00:09.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:09.2: irq 55, io mem 0x20093200
ehci_hcd 0000:00:09.2: USB 2.0 started, EHCI 0.95, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
pnx8550-ohci pnx8550-ohci: PNX8550 OHCI
pnx8550-ohci pnx8550-ohci: new USB bus registered, assigned bus number 2
pnx8550-ohci pnx8550-ohci: irq 13, io mem 0x1be48000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd 0000:00:09.0: OHCI Host Controller
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:09.0: irq 55, io mem 0x20090000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ohci_hcd 0000:00:09.1: OHCI Host Controller
ohci_hcd 0000:00:09.1: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:09.1: irq 55, io mem 0x20091000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
USB Universal Host Controller Interface driver v3.0
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Bridge firewalling registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
eth0: DSPCFG accepted after 0 usec.
eth0: link up.
eth0: Setting full-duplex based on negotiated link capability.
Sending DHCP requests .<5>eth0: increased tx threshold, txcfg 0xd0f01004.
..... timed out!
IP-Config: Reopening network devices...
eth0: DSPCFG accepted after 0 usec.
eth0: link up.
eth0: Setting full-duplex based on negotiated link capability.
Sending DHCP requests .<5>eth0: increased tx threshold, txcfg 0xd0f01004.
., OK
IP-Config: Got DHCP answer from 192.168.1.1, my address is 192.168.1.171
IP-Config: Complete:
      device=eth0, addr=192.168.1.171, mask=255.255.255.0, gw=192.168.1.1,
    host=192.168.1.171, domain=lan, nis-domain=(none),
    bootserver=192.168.1.1, rootserver=192.168.1.1, rootpath=
Freeing unused kernel memory: 2044k freed
Algorithmics/MIPS FPU Emulator v1.5
Loading profile...  done
Mount fstab... done
Remount / read-write... done
Mounting new Root.
enabling SATA modules...sata_sil 0000:00:08.0: Applying R_ERR on DMA activate FIS errata fix
ata1: SATA max UDMA/100 cmd 0xc0058080 ctl 0xc005808a bmdma 0xc0058000 irq 55
ata2: SATA max UDMA/100 cmd 0xc00580c0 ctl 0xc00580ca bmdma 0xc0058008 irq 55
scsi0 : sata_sil
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: ATA-8: Hitachi HTS545050B9A300, PB4OC66G, max UDMA/133
ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/100
scsi1 : sata_sil
ata2: SATA link down (SStatus 0 SControl 310)
scsi 0:0:0:0: Direct-Access    ATA      Hitachi HTS54505 PB4O PQ: 0 ANSI: 5
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
sda: Write Protect is off
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
sda: Write Protect is off
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3
sd 0:0:0:0: Attached scsi disk sda
done
Creating device nodes...done
Setup mdev as hotplug handler... done
Set log level...
Populate /dev... Load luddite and gpio/mmio/rtc...Get display mode and load i2c and fb modules... Detect GPIO function...done
Get System ID...
Restore hotplug handler... done
Restore log level...
Unloading modules...
CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == 801f30dc, ra == c00729e4
Oops[#1]:
Cpu 0
$ 0  : 00000000 10008401 00100100 00000000
$ 4  : 00000000 00000000 c0064304 8110fed8
$ 8  : 803896b0 8110fee1 800a86a8 0000000c
$12  : 43545262 2aab2800 00000000 2aab2800
$16  : c0072e80 c0072e74 00000087 00000480
$20  : 00000000 00000002 00000000 00000003
$24  : 00000000 2acec13c
$28  : 8110e000 8110fe80 7fec0c20 c00729e4
Hi    : 00000372
Lo    : 0002c316
epc  : 801f30dc    Tainted: P
ra    : c00729e4 Status: 10008403    KERNEL EXL IE
Cause : 1080000c
BadVA : 00000000
PrId  : 00061200
Modules linked in: sysid(P) i2c_algo_IP0105 i2c_algo_IP3203 phStbRTC phStbMmio phStbGpio phStbProc lud_pnx8550 lud_core sata_sil libata
Process exe (pid: 312, threadinfo=8110e000, task=86d9b7f0)
Stack : 805b0000 805b0000 0000004f 00030002 80390000 c0072f20 80390000 c00729e4
        805b4e50 80099104 8008dfc0 00000000 800a8844 800a86d4 805b4e50 8008a36c
        8110fec0 8110fec0 00000000 c0072f20 00000480 8110fec8 74536870 43545262
        00000000 00000012 10008400 0000020b 0040369c 2aabdd08 10008400 8008a540
        00000000 80096090 7fec0de1 00000001 00ec0d08 00000480 7fec0de1 00000001
        ...
Call Trace:[<c00729e4>][<80099104>][<8008dfc0>][<800a8844>][<800a86d4>][<8008a36c>][<8008a540>][<80096090>][<80069f00>][<80061d80>]
Code: 8e030000  3c020010  34420100 <ac830000> ae020000  3c020020  34420200  ac640004  ae020004
Shutting down PNX8550 MMIO Driver
Shutting down PNX8550 GPIO driver
Shutting down NXP /proc entries driver
done
done
Mount nfs root /dev/sda1... kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on sda1, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
done
Switch root
INIT: version 2.86 booting
.udev/ already exists on the static /dev! (warning).
Starting the hotplug events dispatcher: udevdudevd[425]: main: the kernel does not support inotify, udevd can't monitor rules file changes
.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...udevd-event[493]: rename_netif: error changing netif name eth0 to eth1: Device or resource busy
Registering SPI driver
Register ProSLIC driver
Setting parameters of disc: (none).
Setting the system clock.
Cannot access the Hardware Clock via any known method.
Use the --debug option to see the details of our search for an access method.
Unable to set System Clock to: Sat Jan 1 00:02:29 UTC 2000 (warning).
Activating swap...done.
Setting the system clock.
Cannot access the Hardware Clock via any known method.
Use the --debug option to see the details of our search for an access method.
Unable to set System Clock to: Sat Jan 1 00:02:31 UTC 2000 (warning).
Cleaning up ifupdown....
Loading kernel modules...done.
Checking file systems...fsck 1.41.3 (12-Oct-2008)
done.
Setting kernel variables (/etc/sysctl.conf)...done.
Mounting local filesystems...kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on sda2, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda3, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
done.
Activating swapfile swap...done.
Setting up networking....
Configuring network interfaces...done.
Luddite version 3, exported  Mon Apr 25 10:40:08 BST 2005
TM0: detected clock 270000000
lud_core: Registering devfs device 0/lud
TM1: detected clock 270000000
lud_core: Registering devfs device 1/lud
NXP /proc entries driver (Aug 13 2007-11:59:40)
dspinfo: Initialising DSP Info Driver
PNX8550 MMIO Driver (Aug 13 2007-11:59:38)
dspmem: Initialising DSP memory Driver
</nowiki>
=== Samba ===
erst mal mounten:
mkdir /mnt/share
'''/etc/fstab'''
/dev/sda3      /mnt/share      ext3    defaults        0      0
'''/etc/samba/smb.conf'''
[share]
path=/mnt/share
browseable=yes
writeable=yes
upstream: 3,69 MB/s
downstream: 3,30 MB/s
=== X11 ===
Ganz wichtig: ''/etc/hosts'' anlegen und ''127.0.0.1 localhost'' eintragen!
apt-get install xdm
apt-get install x11-apps
vim '''/etc/ssh/sshd_config'''
--> hier ''X11Forwarding yes'' hinzufügen
=== VDR ===
Suchlauf:
w_scan -f c -o 6 >/etc/vdr/channels.conf
Das c steht für Cable-Tuner.
danach:
mkdir /var/lib/video.00
sonst startet vdr nicht.
vdr
epg-wird aus dem DVB-C-Anschluss geladen.
=== vdradmin-am ===
Proxy einrichten, damit der Recorder fernbedient werden kann:
ln -s /etc/apache2/mods-available/proxy.load /etc/apache2/mods-enabled/proxy.load
ln -s /etc/apache2/mods-available/proxy.conf /etc/apache2/mods-enabled/proxy.conf
/etc/init.d/apache2 restart
vdr-admin starten:
/etc/init.d/vdradmin-am start
Nutzername/Passwort: ''vim /etc/vdradmin-am/vdradmind.conf'' (linvdr/linvdr)
Host erlauben: ''vim /var/lib/vdr/svdrphosts.conf''
vdr muss laufen und vdradmin-am. Dazu müsse die Berechtigung der Aufnahmeordner gesetzt werden:
chmod 777 /mnt/
chmod 777 /mnt/media/recordings
chmod 777 /mnt/recordings
/etc/init.d/vdr restart
/etc/init.d/vdradmin-am restart

Aktuelle Version vom 29. Juni 2017, 05:16 Uhr

... auch unter dem Namen Pollin-Receiver-Board bekannt.

  • 400 MHz MIPSel
  • 256 MB RAM
  • 64 MB Flash
  • Linux, Windows CE

hacken

Infos

Cable-Tuner: CU1216

Erstinbetriebnahme/Test

  • unteren Scart-Anschluss mit Fernseher verbinden
  • 12 V an linken Stecker anlegen (+Pol vorn, Richtung Bedienteil), Stromaufnahme ca. 1,5 A
  • beide DIP-Schalter (hellblau mit weiß) auf off
  • Taster am äußeren Rand des Bedienteils drücken -> Ein
  • Fernseher zeigt Windows CE 5.0 Oberfläche

"Auslieferungszustand" herstellen

Um weiter basteln zu können, muss eine bestimmte Windows-Version installiert werden: [1]

Ein neu gekauftes Board kann eine andere Version enthalten, deshalb unbedingt reflash durchführen, sonst funktionieren alle folgenden Schritte nicht.

Reflash durchführen:

  • (Board Ausschalten)
  • alle Datei aus dem reflash_wince.rar auf einen FAT32-USB-Stick entpacken
  • Stick an die USB-Buchse unter der LAN-Buchse stecken
  • DIP-Schalter 1 auf on (Firmware-update-Mode)
  • Einschalten (mit Taster auf Bedienteil; entgegen anderer Angaben muss die Fernbedienung nicht benutzt werden)
  • Fernseher zeigt den Updateverlauf
  • Es werden 4 Dateien geladen (7-Segment-Anzeige läuft 4 mal bis 100 %)
  • Windows starten: DIP-Schalter 1 wieder auf off und Reset (Taste hinten) + Einschalttaste

Neue Variante

Es gibt eine relativ sichere Variante. Dazu wird das Elecard-Image benötigt. Es wird gleich das große U-Boot geflasht und bei Bedarf das Elecard-Linux.

Images: [2]

Anleitung: [3]

Flashen

  • DIP-Schalter 1 auf off
  • Board anschalten (Windows CE 5.0 startet)
  • alle Dateien aus u-boot-stick-elecard.tar.gz auf FAT32-USB-Stick kopieren
  • Stick an USB-Buchse auf Rückseite stecken
  • flashme.exe starten
  • "Status: ready..." muss erscheinen, erscheint "Status: error...", muss der "Auslieferungszustand" wiederhergestellt werden.
  • ersten Button klicken: U-Boot wird geflasht
  • warten bis alles fertig ist
  • zweiten Button klicken: Linux wird geflasht
  • warten bis fertig

Jetzt sind die nötigen Dateien drauf. Leider funktioniert Windows CE nicht mehr. Auch wenn das Rettungs-WinCE geflasht wird (3. Button), geht dieses nicht.

Board kann jetzt U-Boot und Linux starten.

Linux starten

Beim Neustart kommen noch 3 Zeilen des Flashers auf der J2. Das richtige U-Boot kommt allerdings auf J33:

  • Pin 1 (markiert): GND
  • Pin 2: Board->PC
  • Pin 4: PC->Board
  • Baud: 38400
  • (Direktverbindung mit PC, keine Pegelwandler)

Das Elecard-Linux kann vom Flash gebootet werden:

  • Board anschalten, U-Boot-Konsole auf J33
  • Autostart scheitert: "ERROR: can't get kernel image!"
  • Partitionen mounten, mit: mtdparts default
  • Linux starten: boot
  • Linux holt sich per DHCP eine IP-Adresse über die LAN-Buchse auf der Rückseite
  • nach erfolgreichem Bezug der Adresse ist die Konsole verfügbar

Linux automatisch starten

Damit Linux nach dem Einschalten automatisch startet muss U-Boot konfiguriert werden.

  • U-Boot-Konsole
  • Alle Variablen anzeigen: printenv
  • nandboot einrichten: setenv nandboot 'mtdparts default;nboot Linux;run ideargs addip;bootm'
  • diese Variable dauerhaft speichern (auch nach reboot verfügbar): saveenv
  • starten geht jetzt auch mit: run nandboot
  • autostart einrichten: setenv bootcmd 'run nandboot'
  • speichern: saveenv
  • neustart: reset
  • jetzt sollte das Board hochfahren
  • wenn U-Boot-Fehlermeldungen kommen, setenv nandboot nochmal durchführen, am besten Zeile kopieren, darauf achten, dass keine Leerzeichen oder ähnliches angehängt werden.

neues rootFS

Es ist möglich ein Debian-rootFS mit dem Elecard-Kernel zu verwenden. Das rootFS gibt es hier: [4]

  • mit gparted zwei primäre ext3-Partitionen auf einen USB-Stick anlegen
  • auf sda1 das rootFS entpacken mit tar -xvjf
  • Stick an Board anstecken
  • Elecard-Kernel booten
  • ssh auf Board mit root/vdr (ip-Adresse? -> die vom dhcp-Server)
  • Ausschalten: reboot
  • niemals direkt ausschalten oder reset drücken, sonst geht das rootFS kaputt und das Bpoard startet nicht mehr -> siehe Debug

Debug

Wenn man etwas nicht funktioniert:

  • "unhandled paging request on adress 00000000" beim Boot: rootFS ist beschädigt, einfach check mit gparted und es funktioniert wieder (wichtig: Stick safely removen)

Alte Variante

Beschreibung unvollständig. Bitte nicht versuchen, die Neue Variante funktioniert.

kleines U-Boot flashen

Um Linux zu starten wird ein Bootloader gebraucht. Dieser kann allerdings zu große um jetzt aufgespielt zu werden. Es wird deshalb erst ein Kleiner installiert, danach der Große.

Das kleine U-Boot: [5]

  • U-Boot.ZIP auf einen FAT32-USB-Stick entpacken
  • Board normal hochfahren (alle Dip-Schalter auf off, am Bedienteil einschalten)
  • USB-Stick und USB-Maus über Hub an Rückseite anstecken
  • myDevices öffnen, USB-Stick darin öffnen, flashme.exe starten
  • Fenster mit "Status: ready..." muss sich öffnen, wenn "Status: error..." dasteht, ist das falsche Windows-Image drauf -> "Auslieferungszustand" wieder herstellen
  • ersten Button klicken -> kleines U-Boot wird geflasht (klassisches Firmware-Update-Programm für "Auslieferungszustand" wiederherstellen wird jetzt ersetzt)
  • zweiter Button: irgend ein Linux-Image wird geflasht (anderer Speicherbereich), kann zusätzlich gemacht werden
  • dritter Button: verändertes Windows-CE, nicht unbedingt flashen, soll flashme automatisch starten, bootet nicht bis zur grafischen Oberfläche, sondern hängt im Ladebalken fest

großes U-Boot flashen

Nachdem nun das kleine U-Boot drauf ist, kann das große U-Boot mit mehr Funktionen aufgespielt werden. Dazu muss das kleine U-Boot gestartet werden:

  • DIP-Schalter 1 auf on
  • Board einschalten (Taste an Bedienteil)

Nach der Linux-Installation

richtig

Determined physical RAM map: memory: 07000000 @ 00000000 (usable) Initrd not found or empty - disabling initrd Built 1 zonelists. Total pages: 28448 Kernel command line: console=ttyS1,38400n8 stb810_display=pal nomainapp=1 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw Primary instruction cache 16kB, physically tagged, 2-way, linesize 32 bytes. Primary data cache 16kB, 4-way, linesize 32 bytes. Synthesized TLB refill handler (23 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB modify handler fastpath (31 instructions). PID hash table entries: 512 (order: 9, 2048 bytes) Using 250.714 MHz high precision timer. Console: colour dummy device 80x25 Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 107648k/114688k available (2841k kernel code, 6996k reserved, 518k data, 2044k init, 0k highmem) Mount-cache hash table entries: 512 NET: Registered protocol family 16 registering PCI controller with io_map_base unset SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Time: MIPS clocksource has been installed. NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NTFS driver 2.1.28 [Flags: R/O]. JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc. io scheduler noop registered io scheduler anticipatory registered (default) Register GPIO SPI device Serial: PNX8XXX driver $Revision: 1.2 $ pnx8xxx-uart: ttyS0 at MMIO 0xbbe4a000 (irq = 27) is a PNX8XXX pnx8xxx-uart: ttyS1 at MMIO 0xbbe4b000 (irq = 28) is a PNX8XXX natsemi dp8381x driver, version 2.1, Sept 11, 2006 originally by Donald Becker <becker@scyld.com> http://www.scyld.com/network/natsemi.html 2.4.x kernel port by Jeff Garzik, Tjeerd Mulder PCI: Enabling device 0000:00:0a.0 (0006 -> 0007) natsemi eth0: NatSemi DP8381[56] at 0x20092000 (0000:00:0a.0), 00:17:31:fb:e4:cd, IRQ 55, port TP. Driver for NAND Flash on the PNX8550 XIO bus (Mar 15 2010-17:54:27) Auto detected a >= 64MByte device on a 8 bit bus NAND device: Manufacturer ID: 0xad, Chip ID: 0x76 (Hynix NAND 64MiB 3,3V 8-bit) Scanning device for bad blocks Creating 8 MTD partitions on "NAND 64MiB 3,3V 8-bit": 0x00000000-0x00004000 : "microBTM" 0x00004000-0x00084000 : "U-Boot" 0x00084000-0x0008c000 : "Env" 0x0008c000-0x00094000 : "bbt" 0x00094000-0x00894000 : "Linux" 0x00894000-0x03b94000 : "ROMFS" 0x03c00000-0x03ff8000 : "WinCE" 0x03ff8000-0x04000000 : "Info" ehci_hcd 0000:00:09.2: EHCI Host Controller ehci_hcd 0000:00:09.2: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:09.2: irq 55, io mem 0x20093200 ehci_hcd 0000:00:09.2: USB 2.0 started, EHCI 0.95, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 4 ports detected pnx8550-ohci pnx8550-ohci: PNX8550 OHCI pnx8550-ohci pnx8550-ohci: new USB bus registered, assigned bus number 2 pnx8550-ohci pnx8550-ohci: irq 13, io mem 0x1be48000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ohci_hcd 0000:00:09.0: OHCI Host Controller ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 3 ohci_hcd 0000:00:09.0: irq 55, io mem 0x20090000 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ohci_hcd 0000:00:09.1: OHCI Host Controller ohci_hcd 0000:00:09.1: new USB bus registered, assigned bus number 4 ohci_hcd 0000:00:09.1: irq 55, io mem 0x20091000 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected USB Universal Host Controller Interface driver v3.0 Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. mice: PS/2 mouse device common for all mice i2c /dev entries driver TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Bridge firewalling registered 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> ieee80211: 802.11 data/management/control stack, git-1.1.13 ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com> eth0: DSPCFG accepted after 0 usec. Sending DHCP requests .....<6>eth0: Autonegotiation advertising 0x5e1 partner 0xcde1. eth0: link up. eth0: Setting full-duplex based on negotiated link capability. .<5>eth0: increased tx threshold, txcfg 0xd0f01004. timed out! IP-Config: Reopening network devices... eth0: DSPCFG accepted after 0 usec. eth0: link up. eth0: Setting full-duplex based on negotiated link capability. Sending DHCP requests .<5>eth0: increased tx threshold, txcfg 0xd0f01004. ., OK IP-Config: Got DHCP answer from 192.168.1.1, my address is 192.168.1.171 IP-Config: Complete: device=eth0, addr=192.168.1.171, mask=255.255.255.0, gw=192.168.1.1, host=192.168.1.171, domain=lan, nis-domain=(none), bootserver=192.168.1.1, rootserver=192.168.1.1, rootpath= Freeing unused kernel memory: 2044k freed Algorithmics/MIPS FPU Emulator v1.5 Loading profile... done Mount fstab... done Remount / read-write... done Mounting new Root. enabling SATA modules...sata_sil 0000:00:08.0: Applying R_ERR on DMA activate FIS errata fix ata1: SATA max UDMA/100 cmd 0xc0058080 ctl 0xc005808a bmdma 0xc0058000 irq 55 ata2: SATA max UDMA/100 cmd 0xc00580c0 ctl 0xc00580ca bmdma 0xc0058008 irq 55 scsi0 : sata_sil ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata1.00: ATA-8: Hitachi HTS545050B9A300, PB4OC66G, max UDMA/133 ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32) ata1.00: configured for UDMA/100 scsi1 : sata_sil ata2: SATA link down (SStatus 0 SControl 310) scsi 0:0:0:0: Direct-Access ATA Hitachi HTS54505 PB4O PQ: 0 ANSI: 5 SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB) sda: Write Protect is off SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB) sda: Write Protect is off SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sd 0:0:0:0: Attached scsi disk sda done Creating device nodes...done Setup mdev as hotplug handler... done Set log level... Populate /dev... Load luddite and gpio/mmio/rtc...Get display mode and load i2c and fb modules... Detect GPIO function...done Get System ID... Restore hotplug handler... done Restore log level... Unloading modules... Shutting down RTC driver Shutting down PNX8550 MMIO Driver Shutting down PNX8550 GPIO driver Shutting down NXP /proc entries driver done done Mount nfs root /dev/sda1... kjournald starting. Commit interval 5 seconds EXT3 FS on sda1, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. done Switch root INIT: version 2.86 booting .udev/ already exists on the static /dev! (warning). Starting the hotplug events dispatcher: udevdudevd[431]: main: the kernel does not support inotify, udevd can't monitor rules file changes . Synthesizing the initial hotplug events...done. Waiting for /dev to be fully populated...udevd-event[506]: rename_netif: error changing netif name eth0 to eth1: Device or resource busy Registering SPI driver Register ProSLIC driver done. Setting the system clock. Cannot access the Hardware Clock via any known method. Use the --debug option to see the details of our search for an access method. Unable to set System Clock to: Sat Jan 1 00:00:26 UTC 2005 (warning). Activating swap...done. Setting the system clock. Cannot access the Hardware Clock via any known method. Use the --debug option to see the details of our search for an access method. Unable to set System Clock to: Sat Jan 1 00:00:27 UTC 2005 (warning). Cleaning up ifupdown.... Loading kernel modules...done. Checking file systems...fsck 1.41.3 (12-Oct-2008) done. Setting kernel variables (/etc/sysctl.conf)...done. Mounting local filesystems...kjournald starting. Commit interval 5 seconds EXT3 FS on sda2, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. done. Activating swapfile swap...done. Setting up networking.... Configuring network interfaces...done. Luddite version 3, exported Mon Apr 25 10:40:08 BST 2005 TM0: detected clock 270000000 lud_core: Registering devfs device 0/lud TM1: detected clock 270000000 lud_core: Registering devfs device 1/lud NXP /proc entries driver (Aug 13 2007-11:59:40) dspinfo: Initialising DSP Info Driver PNX8550 MMIO Driver (Aug 13 2007-11:59:38) dspmem: Initialising DSP memory Driver Philips PNX8550 Demux HW driver (Aug 13 2007-11:59:14) DVB: registering new adapter (pnx8550vmsp0). DVB: registering new adapter (pnx8550vmsp1). DVB: registering new adapter (pnx8550pdma0). DVB: registering new adapter (pnx8550pdma1). NXP PNX8550 DVB adapter driver Analog Backend driver (Aug 13 2007-11:59:55) AK470X (AV Scart switch) driver (Aug 13 2007-11:59:57) - Device AK4706 Loopthrough disabled Using specified video mode (PAL-CVBS) vdenc0: PNX8550 Internal Vdenc video denc device Dbg driver (Feb 20 2008-12:40:20) TriMedia RPC driver Debug Buffer Print driver (Aug 13 2007-11:59:09) RTC driver (Aug 13 2007-11:59:41) PNX8550 GPIO driver (Aug 13 2007-11:59:32) SAA8510 (Anabel) driver Using specified video mode (PAL-RGB) vdenc1: PNX8510 Driver video denc device STB-810 ALSA Audio Driver (Aug 13 2007-11:59:07) pnxdraw: Initialised (Compiled Aug 13 2007-11:59:22) Cannot open luddite device - Error = -1 open tmdev: No such file or directory Cannot open luddite device - Error = -1 open tmdev: No such file or directory INIT: Entering runlevel: 2 Starting enhanced syslogd: rsyslogd. Starting OpenBSD Secure Shell server: sshd. ################################################## ## LIRC IS NOT CONFIGURED ## ## ## ## read /usr/share/doc/lirc/html/configure.html ## ################################################## Additional hint: Either /etc/lirc/lircd.conf or /etc/lirc/hardware.conf doesn't exist or either of the two has the string UNCONFIGURED in it at some important place. Try: 'dpkg-reconfigure lirc' Starting lirc daemon:. Starting Linux Video Disk Recorder: vdr Searching for plugins (VDR 1.6.0-2/1.6.0) (cache hit): xvdr streamdev-server. Starting VDR Webadministration interface: - aborted (to enable the daemon, edit /etc/default/vdradmin-am)Starting periodic command scheduler: crond. eth0: increased tx threshold, txcfg 0xd0f01006. eth0: increased tx threshold, txcfg 0xd0f01008.

falsch

Data Size: 3233500 Bytes = 3.1 MiB Load Address: 80060000 Entry Point: 803a9000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Starting kernel ... Determined physical RAM map: memory: 07000000 @ 00000000 (usable) Initrd not found or empty - disabling initrd Built 1 zonelists. Total pages: 28448 Kernel command line: console=ttyS1,38400n8 stb810_display=pal nomainapp=1 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw Primary instruction cache 16kB, physically tagged, 2-way, linesize 32 bytes. Primary data cache 16kB, 4-way, linesize 32 bytes. Synthesized TLB refill handler (23 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB modify handler fastpath (31 instructions). PID hash table entries: 512 (order: 9, 2048 bytes) Using 250.714 MHz high precision timer. Linux version 2.6.21.3PNX8550 (root@smithy) (gcc version 4.0.0 (DENX ELDK 4.0 4.0.0)) #1743 Fri Feb 11 10:49:15 OMST 2011 Setting initial splash screen display mode SD (50Hz) CPU revision is: 00061200 Determined physical RAM map: memory: 07000000 @ 00000000 (usable) Initrd not found or empty - disabling initrd Built 1 zonelists. Total pages: 28448 Kernel command line: console=ttyS1,38400n8 stb810_display=pal nomainapp=1 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw Primary instruction cache 16kB, physically tagged, 2-way, linesize 32 bytes. Primary data cache 16kB, 4-way, linesize 32 bytes. Synthesized TLB refill handler (23 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB modify handler fastpath (31 instructions). PID hash table entries: 512 (order: 9, 2048 bytes) Using 250.714 MHz high precision timer. Console: colour dummy device 80x25 Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 107648k/114688k available (2841k kernel code, 6996k reserved, 518k data, 2044k init, 0k highmem) Mount-cache hash table entries: 512 NET: Registered protocol family 16 registering PCI controller with io_map_base unset SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Time: MIPS clocksource has been installed. NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NTFS driver 2.1.28 [Flags: R/O]. JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc. io scheduler noop registered io scheduler anticipatory registered (default) Register GPIO SPI device Serial: PNX8XXX driver $Revision: 1.2 $ pnx8xxx-uart: ttyS0 at MMIO 0xbbe4a000 (irq = 27) is a PNX8XXX pnx8xxx-uart: ttyS1 at MMIO 0xbbe4b000 (irq = 28) is a PNX8XXX natsemi dp8381x driver, version 2.1, Sept 11, 2006 originally by Donald Becker <becker@scyld.com> http://www.scyld.com/network/natsemi.html 2.4.x kernel port by Jeff Garzik, Tjeerd Mulder PCI: Enabling device 0000:00:0a.0 (0006 -> 0007) natsemi eth0: NatSemi DP8381[56] at 0x20092000 (0000:00:0a.0), 00:17:31:fb:e4:cd, IRQ 55, port TP. Driver for NAND Flash on the PNX8550 XIO bus (Mar 15 2010-17:54:27) Auto detected a >= 64MByte device on a 8 bit bus NAND device: Manufacturer ID: 0xad, Chip ID: 0x76 (Hynix NAND 64MiB 3,3V 8-bit) Scanning device for bad blocks Creating 8 MTD partitions on "NAND 64MiB 3,3V 8-bit": 0x00000000-0x00004000 : "microBTM" 0x00004000-0x00084000 : "U-Boot" 0x00084000-0x0008c000 : "Env" 0x0008c000-0x00094000 : "bbt" 0x00094000-0x00894000 : "Linux" 0x00894000-0x03b94000 : "ROMFS" 0x03c00000-0x03ff8000 : "WinCE" 0x03ff8000-0x04000000 : "Info" ehci_hcd 0000:00:09.2: EHCI Host Controller ehci_hcd 0000:00:09.2: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:09.2: irq 55, io mem 0x20093200 ehci_hcd 0000:00:09.2: USB 2.0 started, EHCI 0.95, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 4 ports detected pnx8550-ohci pnx8550-ohci: PNX8550 OHCI pnx8550-ohci pnx8550-ohci: new USB bus registered, assigned bus number 2 pnx8550-ohci pnx8550-ohci: irq 13, io mem 0x1be48000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ohci_hcd 0000:00:09.0: OHCI Host Controller ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 3 ohci_hcd 0000:00:09.0: irq 55, io mem 0x20090000 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ohci_hcd 0000:00:09.1: OHCI Host Controller ohci_hcd 0000:00:09.1: new USB bus registered, assigned bus number 4 ohci_hcd 0000:00:09.1: irq 55, io mem 0x20091000 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected USB Universal Host Controller Interface driver v3.0 Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. mice: PS/2 mouse device common for all mice i2c /dev entries driver TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Bridge firewalling registered 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> ieee80211: 802.11 data/management/control stack, git-1.1.13 ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com> eth0: DSPCFG accepted after 0 usec. eth0: link up. eth0: Setting full-duplex based on negotiated link capability. Sending DHCP requests .<5>eth0: increased tx threshold, txcfg 0xd0f01004. ..... timed out! IP-Config: Reopening network devices... eth0: DSPCFG accepted after 0 usec. eth0: link up. eth0: Setting full-duplex based on negotiated link capability. Sending DHCP requests .<5>eth0: increased tx threshold, txcfg 0xd0f01004. ., OK IP-Config: Got DHCP answer from 192.168.1.1, my address is 192.168.1.171 IP-Config: Complete: device=eth0, addr=192.168.1.171, mask=255.255.255.0, gw=192.168.1.1, host=192.168.1.171, domain=lan, nis-domain=(none), bootserver=192.168.1.1, rootserver=192.168.1.1, rootpath= Freeing unused kernel memory: 2044k freed Algorithmics/MIPS FPU Emulator v1.5 Loading profile... done Mount fstab... done Remount / read-write... done Mounting new Root. enabling SATA modules...sata_sil 0000:00:08.0: Applying R_ERR on DMA activate FIS errata fix ata1: SATA max UDMA/100 cmd 0xc0058080 ctl 0xc005808a bmdma 0xc0058000 irq 55 ata2: SATA max UDMA/100 cmd 0xc00580c0 ctl 0xc00580ca bmdma 0xc0058008 irq 55 scsi0 : sata_sil ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata1.00: ATA-8: Hitachi HTS545050B9A300, PB4OC66G, max UDMA/133 ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32) ata1.00: configured for UDMA/100 scsi1 : sata_sil ata2: SATA link down (SStatus 0 SControl 310) scsi 0:0:0:0: Direct-Access ATA Hitachi HTS54505 PB4O PQ: 0 ANSI: 5 SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB) sda: Write Protect is off SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB) sda: Write Protect is off SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sd 0:0:0:0: Attached scsi disk sda done Creating device nodes...done Setup mdev as hotplug handler... done Set log level... Populate /dev... Load luddite and gpio/mmio/rtc...Get display mode and load i2c and fb modules... Detect GPIO function...done Get System ID... Restore hotplug handler... done Restore log level... Unloading modules... CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == 801f30dc, ra == c00729e4 Oops[#1]: Cpu 0 $ 0  : 00000000 10008401 00100100 00000000 $ 4  : 00000000 00000000 c0064304 86e39ed8 $ 8  : 803896b0 86e39ee1 800a86a8 0000000c $12  : 43545262 2aab2800 00000000 2aab2800 $16  : c0072e80 c0072e74 00000087 00000480 $20  : 00000000 00000002 00000000 00000003 $24  : 00000000 2acec13c $28  : 86e38000 86e39e80 7f9bec20 c00729e4 Hi  : 00000372 Lo  : 0002c316 epc  : 801f30dc Tainted: P ra  : c00729e4 Status: 10008403 KERNEL EXL IE Cause : 1080000c BadVA : 00000000 PrId  : 00061200 Modules linked in: sysid(P) i2c_algo_IP0105 i2c_algo_IP3203 phStbRTC phStbMmio phStbGpio phStbProc lud_pnx8550 lud_core sata_sil libata Process exe (pid: 312, threadinfo=86e38000, task=811027f0) Stack : 805b0000 805b0000 0000004f 00030002 80390000 c0072f20 80390000 c00729e4 805b4e50 80099104 8008dfc0 0002ad9b 800a8844 800a86d4 805b4e50 8008a36c 86e39ec0 86e39ec0 00000000 c0072f20 00000480 86e39ec8 74536870 43545262 00000200 00000001 10008400 10002ea8 2aafdcb8 004068c8 10008400 8008a540 00000000 80096090 7f9bede1 00000001 009bed08 00000480 7f9bede1 00000001 ... Call Trace:[<c00729e4>][<80099104>][<8008dfc0>][<800a8844>][<800a86d4>][<8008a36c>][<8008a540>][<80096090>][<80069f00>][<80061d80>] Code: 8e030000 3c020010 34420100 <ac830000> ae020000 3c020020 34420200 ac640004 ae020004 Shutting down PNX8550 MMIO Driver Shutting down PNX8550 GPIO driver Shutting down NXP /proc entries driver done done Mount nfs root /dev/sda1... kjournald starting. Commit interval 5 seconds EXT3 FS on sda1, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. done Switch root INIT: version 2.86 booting .udev/ already exists on the static /dev! (warning). Starting the hotplug events dispatcher: udevdudevd[425]: main: the kernel does not support inotify, udevd can't monitor rules file changes . Synthesizing the initial hotplug events...done. Waiting for /dev to be fully populated...udevd-event[493]: rename_netif: error changing netif name eth0 to eth1: Device or resource busy Registering SPI driver Register ProSLIC driver à U-Boot 2011.09-00000-gf54ce7f-dirty (Dec 20 2011 - 12:36:29) DRAM: 128 MiB NAND: NAND device: Manufacturer ID: 0xad, Chip ID: 0x76 (Hynix NAND 64MiB 3,3V 8-bit) 64 MiB Bad block table at page 1120, version 0x01 Bad block table at page 1152, version 0x01 In: serial Out: serial Err: serial Net: natsemi: EEPROM contents: d008 0400 0b34 00f3 0000 0000 0000 8b80 7d98 66f2 0000 aae2 natsemi: MAC-Address: 0:17:31:FB:E4:CD dp83815#0 Welcome to the pollinux board v1.1 Hit any key to stop autoboot: 0 Loading from nand0, offset 0x94000 Image Name: Elecard Linux 2.6 Created: 2011-12-07 16:01:46 UTC Image Type: MIPS Elecard Linux Kernel Image (gzip compressed) Data Size: 3233500 Bytes = 3.1 MiB Load Address: 80060000 Entry Point: 803a9000 ** Too many args (max. 16) ** ** Too many args (max. 16) ** ## Booting kernel from Legacy Image at 82000000 ... Image Name: Elecard Linux 2.6 Created: 2011-12-07 16:01:46 UTC Image Type: MIPS Elecard Linux Kernel Image (gzip compressed) Data Size: 3233500 Bytes = 3.1 MiB Load Address: 80060000 Entry Point: 803a9000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Starting kernel ... Determined physical RAM map: memory: 07000000 @ 00000000 (usable) Initrd not found or empty - disabling initrd Built 1 zonelists. Total pages: 28448 Kernel command line: console=ttyS1,38400n8 stb810_display=pal nomainapp=1 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw Primary instruction cache 16kB, physically tagged, 2-way, linesize 32 bytes. Primary data cache 16kB, 4-way, linesize 32 bytes. Synthesized TLB refill handler (23 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB modify handler fastpath (31 instructions). PID hash table entries: 512 (order: 9, 2048 bytes) Using 250.714 MHz high precision timer. Linux version 2.6.21.3PNX8550 (root@smithy) (gcc version 4.0.0 (DENX ELDK 4.0 4.0.0)) #1743 Fri Feb 11 10:49:15 OMST 2011 Setting initial splash screen display mode SD (50Hz) CPU revision is: 00061200 Determined physical RAM map: memory: 07000000 @ 00000000 (usable) Initrd not found or empty - disabling initrd Built 1 zonelists. Total pages: 28448 Kernel command line: console=ttyS1,38400n8 stb810_display=pal nomainapp=1 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw Primary instruction cache 16kB, physically tagged, 2-way, linesize 32 bytes. Primary data cache 16kB, 4-way, linesize 32 bytes. Synthesized TLB refill handler (23 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB modify handler fastpath (31 instructions). PID hash table entries: 512 (order: 9, 2048 bytes) Using 250.714 MHz high precision timer. Console: colour dummy device 80x25 Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 107648k/114688k available (2841k kernel code, 6996k reserved, 518k data, 2044k init, 0k highmem) Mount-cache hash table entries: 512 NET: Registered protocol family 16 registering PCI controller with io_map_base unset SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Time: MIPS clocksource has been installed. NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NTFS driver 2.1.28 [Flags: R/O]. JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc. io scheduler noop registered io scheduler anticipatory registered (default) Register GPIO SPI device Serial: PNX8XXX driver $Revision: 1.2 $ pnx8xxx-uart: ttyS0 at MMIO 0xbbe4a000 (irq = 27) is a PNX8XXX pnx8xxx-uart: ttyS1 at MMIO 0xbbe4b000 (irq = 28) is a PNX8XXX natsemi dp8381x driver, version 2.1, Sept 11, 2006 originally by Donald Becker <becker@scyld.com> http://www.scyld.com/network/natsemi.html 2.4.x kernel port by Jeff Garzik, Tjeerd Mulder PCI: Enabling device 0000:00:0a.0 (0006 -> 0007) natsemi eth0: NatSemi DP8381[56] at 0x20092000 (0000:00:0a.0), 00:17:31:fb:e4:cd, IRQ 55, port TP. Driver for NAND Flash on the PNX8550 XIO bus (Mar 15 2010-17:54:27) Auto detected a >= 64MByte device on a 8 bit bus NAND device: Manufacturer ID: 0xad, Chip ID: 0x76 (Hynix NAND 64MiB 3,3V 8-bit) Scanning device for bad blocks Creating 8 MTD partitions on "NAND 64MiB 3,3V 8-bit": 0x00000000-0x00004000 : "microBTM" 0x00004000-0x00084000 : "U-Boot" 0x00084000-0x0008c000 : "Env" 0x0008c000-0x00094000 : "bbt" 0x00094000-0x00894000 : "Linux" 0x00894000-0x03b94000 : "ROMFS" 0x03c00000-0x03ff8000 : "WinCE" 0x03ff8000-0x04000000 : "Info" ehci_hcd 0000:00:09.2: EHCI Host Controller ehci_hcd 0000:00:09.2: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:09.2: irq 55, io mem 0x20093200 ehci_hcd 0000:00:09.2: USB 2.0 started, EHCI 0.95, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 4 ports detected pnx8550-ohci pnx8550-ohci: PNX8550 OHCI pnx8550-ohci pnx8550-ohci: new USB bus registered, assigned bus number 2 pnx8550-ohci pnx8550-ohci: irq 13, io mem 0x1be48000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ohci_hcd 0000:00:09.0: OHCI Host Controller ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 3 ohci_hcd 0000:00:09.0: irq 55, io mem 0x20090000 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ohci_hcd 0000:00:09.1: OHCI Host Controller ohci_hcd 0000:00:09.1: new USB bus registered, assigned bus number 4 ohci_hcd 0000:00:09.1: irq 55, io mem 0x20091000 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected USB Universal Host Controller Interface driver v3.0 Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. mice: PS/2 mouse device common for all mice i2c /dev entries driver TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Bridge firewalling registered 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> ieee80211: 802.11 data/management/control stack, git-1.1.13 ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com> eth0: DSPCFG accepted after 0 usec. eth0: link up. eth0: Setting full-duplex based on negotiated link capability. Sending DHCP requests .<5>eth0: increased tx threshold, txcfg 0xd0f01004. ..... timed out! IP-Config: Reopening network devices... eth0: DSPCFG accepted after 0 usec. eth0: link up. eth0: Setting full-duplex based on negotiated link capability. Sending DHCP requests .<5>eth0: increased tx threshold, txcfg 0xd0f01004. ., OK IP-Config: Got DHCP answer from 192.168.1.1, my address is 192.168.1.171 IP-Config: Complete: device=eth0, addr=192.168.1.171, mask=255.255.255.0, gw=192.168.1.1, host=192.168.1.171, domain=lan, nis-domain=(none), bootserver=192.168.1.1, rootserver=192.168.1.1, rootpath= Freeing unused kernel memory: 2044k freed Algorithmics/MIPS FPU Emulator v1.5 Loading profile... done Mount fstab... done Remount / read-write... done Mounting new Root. enabling SATA modules...sata_sil 0000:00:08.0: Applying R_ERR on DMA activate FIS errata fix ata1: SATA max UDMA/100 cmd 0xc0058080 ctl 0xc005808a bmdma 0xc0058000 irq 55 ata2: SATA max UDMA/100 cmd 0xc00580c0 ctl 0xc00580ca bmdma 0xc0058008 irq 55 scsi0 : sata_sil ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata1.00: ATA-8: Hitachi HTS545050B9A300, PB4OC66G, max UDMA/133 ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32) ata1.00: configured for UDMA/100 scsi1 : sata_sil ata2: SATA link down (SStatus 0 SControl 310) scsi 0:0:0:0: Direct-Access ATA Hitachi HTS54505 PB4O PQ: 0 ANSI: 5 SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB) sda: Write Protect is off SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB) sda: Write Protect is off SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sd 0:0:0:0: Attached scsi disk sda done Creating device nodes...done Setup mdev as hotplug handler... done Set log level... Populate /dev... Load luddite and gpio/mmio/rtc...Get display mode and load i2c and fb modules... Detect GPIO function...done Get System ID... Restore hotplug handler... done Restore log level... Unloading modules... CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == 801f30dc, ra == c00729e4 Oops[#1]: Cpu 0 $ 0  : 00000000 10008401 00100100 00000000 $ 4  : 00000000 00000000 c0064304 8110fed8 $ 8  : 803896b0 8110fee1 800a86a8 0000000c $12  : 43545262 2aab2800 00000000 2aab2800 $16  : c0072e80 c0072e74 00000087 00000480 $20  : 00000000 00000002 00000000 00000003 $24  : 00000000 2acec13c $28  : 8110e000 8110fe80 7fdb3c20 c00729e4 Hi  : 00000372 Lo  : 0002c316 epc  : 801f30dc Tainted: P ra  : c00729e4 Status: 10008403 KERNEL EXL IE Cause : 1080000c BadVA : 00000000 PrId  : 00061200 Modules linked in: sysid(P) i2c_algo_IP0105 i2c_algo_IP3203 phStbRTC phStbMmio phStbGpio phStbProc lud_pnx8550 lud_core sata_sil libata Process exe (pid: 312, threadinfo=8110e000, task=86d9b7f0) Stack : 805b0000 805b0000 0000004f 00030002 80390000 c0072f20 80390000 c00729e4 805b4e50 80099104 8008dfc0 0002ad9b 800a8844 800a86d4 805b4e50 8008a36c 8110fec0 8110fec0 00000000 c0072f20 00000480 8110fec8 74536870 43545262 00000200 00000001 10008400 10002ed8 2aafdcb8 004068e0 10008400 8008a540 00000000 80096090 7fdb3de1 00000001 00db3d08 00000480 7fdb3de1 00000001 ... Call Trace:[<c00729e4>][<80099104>][<8008dfc0>][<800a8844>][<800a86d4>][<8008a36c>][<8008a540>][<80096090>][<80069f00>][<80061d80>] Code: 8e030000 3c020010 34420100 <ac830000> ae020000 3c020020 34420200 ac640004 ae020004 Shutting down PNX8550 MMIO Driver Shutting down PNX8550 GPIO driver Shutting down NXP /proc entries driver done done Mount nfs root /dev/sda1... kjournald starting. Commit interval 5 seconds EXT3 FS on sda1, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. done Switch root INIT: version 2.86 booting .udev/ already exists on the static /dev! (warning). Starting the hotplug events dispatcher: udevdudevd[425]: main: the kernel does not support inotify, udevd can't monitor rules file changes . Synthesizing the initial hotplug events...done. Waiting for /dev to be fully populated...udevd-event[497]: rename_netif: error changing netif name eth0 to eth1: Device or resource busy Registering SPI driver Register ProSLIC driver à U-Boot 2011.09-00000-gf54ce7f-dirty (Dec 20 2011 - 12:36:29) DRAM: 128 MiB NAND: NAND device: Manufacturer ID: 0xad, Chip ID: 0x76 (Hynix NAND 64MiB 3,3V 8-bit) 64 MiB Bad block table at page 1120, version 0x01 Bad block table at page 1152, version 0x01 In: serial Out: serial Err: serial Net: natsemi: EEPROM contents: d008 0400 0b34 00f3 0000 0000 0000 8b80 7d98 66f2 0000 aae2 natsemi: MAC-Address: 0:17:31:FB:E4:CD dp83815#0 Welcome to the pollinux board v1.1 Hit any key to stop autoboot: 0 Loading from nand0, offset 0x94000 Image Name: Elecard Linux 2.6 Created: 2011-12-07 16:01:46 UTC Image Type: MIPS Elecard Linux Kernel Image (gzip compressed) Data Size: 3233500 Bytes = 3.1 MiB Load Address: 80060000 Entry Point: 803a9000 ** Too many args (max. 16) ** ** Too many args (max. 16) ** ## Booting kernel from Legacy Image at 82000000 ... Image Name: Elecard Linux 2.6 Created: 2011-12-07 16:01:46 UTC Image Type: MIPS Elecard Linux Kernel Image (gzip compressed) Data Size: 3233500 Bytes = 3.1 MiB Load Address: 80060000 Entry Point: 803a9000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Starting kernel ... Determined physical RAM map: memory: 07000000 @ 00000000 (usable) Initrd not found or empty - disabling initrd Built 1 zonelists. Total pages: 28448 Kernel command line: console=ttyS1,38400n8 stb810_display=pal nomainapp=1 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw Primary instruction cache 16kB, physically tagged, 2-way, linesize 32 bytes. Primary data cache 16kB, 4-way, linesize 32 bytes. Synthesized TLB refill handler (23 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB modify handler fastpath (31 instructions). PID hash table entries: 512 (order: 9, 2048 bytes) Using 250.714 MHz high precision timer. Linux version 2.6.21.3PNX8550 (root@smithy) (gcc version 4.0.0 (DENX ELDK 4.0 4.0.0)) #1743 Fri Feb 11 10:49:15 OMST 2011 Setting initial splash screen display mode SD (50Hz) CPU revision is: 00061200 Determined physical RAM map: memory: 07000000 @ 00000000 (usable) Initrd not found or empty - disabling initrd Built 1 zonelists. Total pages: 28448 Kernel command line: console=ttyS1,38400n8 stb810_display=pal nomainapp=1 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw Primary instruction cache 16kB, physically tagged, 2-way, linesize 32 bytes. Primary data cache 16kB, 4-way, linesize 32 bytes. Synthesized TLB refill handler (23 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB modify handler fastpath (31 instructions). PID hash table entries: 512 (order: 9, 2048 bytes) Using 250.714 MHz high precision timer. Console: colour dummy device 80x25 Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 107648k/114688k available (2841k kernel code, 6996k reserved, 518k data, 2044k init, 0k highmem) Mount-cache hash table entries: 512 NET: Registered protocol family 16 registering PCI controller with io_map_base unset SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Time: MIPS clocksource has been installed. NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NTFS driver 2.1.28 [Flags: R/O]. JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc. io scheduler noop registered io scheduler anticipatory registered (default) Register GPIO SPI device Serial: PNX8XXX driver $Revision: 1.2 $ pnx8xxx-uart: ttyS0 at MMIO 0xbbe4a000 (irq = 27) is a PNX8XXX pnx8xxx-uart: ttyS1 at MMIO 0xbbe4b000 (irq = 28) is a PNX8XXX natsemi dp8381x driver, version 2.1, Sept 11, 2006 originally by Donald Becker <becker@scyld.com> http://www.scyld.com/network/natsemi.html 2.4.x kernel port by Jeff Garzik, Tjeerd Mulder PCI: Enabling device 0000:00:0a.0 (0006 -> 0007) natsemi eth0: NatSemi DP8381[56] at 0x20092000 (0000:00:0a.0), 00:17:31:fb:e4:cd, IRQ 55, port TP. Driver for NAND Flash on the PNX8550 XIO bus (Mar 15 2010-17:54:27) Auto detected a >= 64MByte device on a 8 bit bus NAND device: Manufacturer ID: 0xad, Chip ID: 0x76 (Hynix NAND 64MiB 3,3V 8-bit) Scanning device for bad blocks Creating 8 MTD partitions on "NAND 64MiB 3,3V 8-bit": 0x00000000-0x00004000 : "microBTM" 0x00004000-0x00084000 : "U-Boot" 0x00084000-0x0008c000 : "Env" 0x0008c000-0x00094000 : "bbt" 0x00094000-0x00894000 : "Linux" 0x00894000-0x03b94000 : "ROMFS" 0x03c00000-0x03ff8000 : "WinCE" 0x03ff8000-0x04000000 : "Info" ehci_hcd 0000:00:09.2: EHCI Host Controller ehci_hcd 0000:00:09.2: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:09.2: irq 55, io mem 0x20093200 ehci_hcd 0000:00:09.2: USB 2.0 started, EHCI 0.95, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 4 ports detected pnx8550-ohci pnx8550-ohci: PNX8550 OHCI pnx8550-ohci pnx8550-ohci: new USB bus registered, assigned bus number 2 pnx8550-ohci pnx8550-ohci: irq 13, io mem 0x1be48000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ohci_hcd 0000:00:09.0: OHCI Host Controller ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 3 ohci_hcd 0000:00:09.0: irq 55, io mem 0x20090000 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ohci_hcd 0000:00:09.1: OHCI Host Controller ohci_hcd 0000:00:09.1: new USB bus registered, assigned bus number 4 ohci_hcd 0000:00:09.1: irq 55, io mem 0x20091000 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected USB Universal Host Controller Interface driver v3.0 Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. mice: PS/2 mouse device common for all mice i2c /dev entries driver TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Bridge firewalling registered 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> ieee80211: 802.11 data/management/control stack, git-1.1.13 ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com> eth0: DSPCFG accepted after 0 usec. eth0: link up. eth0: Setting full-duplex based on negotiated link capability. Sending DHCP requests .<5>eth0: increased tx threshold, txcfg 0xd0f01004. ..... timed out! IP-Config: Reopening network devices... eth0: DSPCFG accepted after 0 usec. eth0: link up. eth0: Setting full-duplex based on negotiated link capability. Sending DHCP requests .<5>eth0: increased tx threshold, txcfg 0xd0f01004. ., OK IP-Config: Got DHCP answer from 192.168.1.1, my address is 192.168.1.171 IP-Config: Complete: device=eth0, addr=192.168.1.171, mask=255.255.255.0, gw=192.168.1.1, host=192.168.1.171, domain=lan, nis-domain=(none), bootserver=192.168.1.1, rootserver=192.168.1.1, rootpath= Freeing unused kernel memory: 2044k freed Algorithmics/MIPS FPU Emulator v1.5 Loading profile... done Mount fstab... done Remount / read-write... done Mounting new Root. enabling SATA modules...sata_sil 0000:00:08.0: Applying R_ERR on DMA activate FIS errata fix ata1: SATA max UDMA/100 cmd 0xc0058080 ctl 0xc005808a bmdma 0xc0058000 irq 55 ata2: SATA max UDMA/100 cmd 0xc00580c0 ctl 0xc00580ca bmdma 0xc0058008 irq 55 scsi0 : sata_sil ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata1.00: ATA-8: Hitachi HTS545050B9A300, PB4OC66G, max UDMA/133 ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32) ata1.00: configured for UDMA/100 scsi1 : sata_sil ata2: SATA link down (SStatus 0 SControl 310) scsi 0:0:0:0: Direct-Access ATA Hitachi HTS54505 PB4O PQ: 0 ANSI: 5 SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB) sda: Write Protect is off SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB) sda: Write Protect is off SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sd 0:0:0:0: Attached scsi disk sda done Creating device nodes...done Setup mdev as hotplug handler... done Set log level... Populate /dev... Load luddite and gpio/mmio/rtc...Get display mode and load i2c and fb modules... Detect GPIO function...done Get System ID... Restore hotplug handler... done Restore log level... Unloading modules... CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == 801f30dc, ra == c00729e4 Oops[#1]: Cpu 0 $ 0  : 00000000 10008401 00100100 00000000 $ 4  : 00000000 00000000 c0064304 86e39ed8 $ 8  : 803896b0 86e39ee1 800a86a8 0000000c $12  : 43545262 2aab2800 00000000 2aab2800 $16  : c0072e80 c0072e74 00000087 00000480 $20  : 00000000 00000002 00000000 00000003 $24  : 00000000 2acec13c $28  : 86e38000 86e39e80 7ffc3c20 c00729e4 Hi  : 00000372 Lo  : 0002c316 epc  : 801f30dc Tainted: P ra  : c00729e4 Status: 10008403 KERNEL EXL IE Cause : 1080000c BadVA : 00000000 PrId  : 00061200 Modules linked in: sysid(P) i2c_algo_IP0105 i2c_algo_IP3203 phStbRTC phStbMmio phStbGpio phStbProc lud_pnx8550 lud_core sata_sil libata Process exe (pid: 312, threadinfo=86e38000, task=81116000) Stack : 805b0000 805b0000 0000004f 00030002 80390000 c0072f20 80390000 c00729e4 805b4e50 80099104 8008dfc0 00000000 800a8844 800a86d4 805b4e50 8008a36c 86e39ec0 86e39ec0 00000000 c0072f20 00000480 86e39ec8 74536870 43545262 00000000 00000012 10008400 00000201 004035fc 2aabdd08 10008400 8008a540 00000000 80096090 7ffc3de1 00000001 00fc3d08 00000480 7ffc3de1 00000001 ... Call Trace:[<c00729e4>][<80099104>][<8008dfc0>][<800a8844>][<800a86d4>][<8008a36c>][<8008a540>][<80096090>][<80069f00>][<80061d80>] Code: 8e030000 3c020010 34420100 <ac830000> ae020000 3c020020 34420200 ac640004 ae020004 Shutting down PNX8550 MMIO Driver Shutting down PNX8550 GPIO driver Shutting down NXP /proc entries driver done done Mount nfs root /dev/sda1... kjournald starting. Commit interval 5 seconds EXT3 FS on sda1, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. done Switch root INIT: version 2.86 booting .udev/ already exists on the static /dev! (warning). Starting the hotplug events dispatcher: udevdudevd[425]: main: the kernel does not support inotify, udevd can't monitor rules file changes . Synthesizing the initial hotplug events...done. Waiting for /dev to be fully populated...udevd-event[496]: rename_netif: error changing netif name eth0 to eth1: Device or resource busy Registering SPI driver Register ProSLIC driver à U-Boot 2011.09-00000-gf54ce7f-dirty (Dec 20 2011 - 12:36:29) DRAM: 128 MiB NAND: NAND device: Manufacturer ID: 0xad, Chip ID: 0x76 (Hynix NAND 64MiB 3,3V 8-bit) 64 MiB Bad block table at page 1120, version 0x01 Bad block table at page 1152, version 0x01 In: serial Out: serial Err: serial Net: natsemi: EEPROM contents: d008 0400 0b34 00f3 0000 0000 0000 8b80 7d98 66f2 0000 aae2 natsemi: MAC-Address: 0:17:31:FB:E4:CD dp83815#0 Welcome to the pollinux board v1.1 Hit any key to stop autoboot: 0 Loading from nand0, offset 0x94000 Image Name: Elecard Linux 2.6 Created: 2011-12-07 16:01:46 UTC Image Type: MIPS Elecard Linux Kernel Image (gzip compressed) Data Size: 3233500 Bytes = 3.1 MiB Load Address: 80060000 Entry Point: 803a9000 ** Too many args (max. 16) ** ** Too many args (max. 16) ** ## Booting kernel from Legacy Image at 82000000 ... Image Name: Elecard Linux 2.6 Created: 2011-12-07 16:01:46 UTC Image Type: MIPS Elecard Linux Kernel Image (gzip compressed) Data Size: 3233500 Bytes = 3.1 MiB Load Address: 80060000 Entry Point: 803a9000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Starting kernel ... Determined physical RAM map: memory: 07000000 @ 00000000 (usable) Initrd not found or empty - disabling initrd Built 1 zonelists. Total pages: 28448 Kernel command line: console=ttyS1,38400n8 stb810_display=pal nomainapp=1 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw Primary instruction cache 16kB, physically tagged, 2-way, linesize 32 bytes. Primary data cache 16kB, 4-way, linesize 32 bytes. Synthesized TLB refill handler (23 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB modify handler fastpath (31 instructions). PID hash table entries: 512 (order: 9, 2048 bytes) Using 250.714 MHz high precision timer. Linux version 2.6.21.3PNX8550 (root@smithy) (gcc version 4.0.0 (DENX ELDK 4.0 4.0.0)) #1743 Fri Feb 11 10:49:15 OMST 2011 Setting initial splash screen display mode SD (50Hz) CPU revision is: 00061200 Determined physical RAM map: memory: 07000000 @ 00000000 (usable) Initrd not found or empty - disabling initrd Built 1 zonelists. Total pages: 28448 Kernel command line: console=ttyS1,38400n8 stb810_display=pal nomainapp=1 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw Primary instruction cache 16kB, physically tagged, 2-way, linesize 32 bytes. Primary data cache 16kB, 4-way, linesize 32 bytes. Synthesized TLB refill handler (23 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB modify handler fastpath (31 instructions). PID hash table entries: 512 (order: 9, 2048 bytes) Using 250.714 MHz high precision timer. Console: colour dummy device 80x25 Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 107648k/114688k available (2841k kernel code, 6996k reserved, 518k data, 2044k init, 0k highmem) Mount-cache hash table entries: 512 NET: Registered protocol family 16 registering PCI controller with io_map_base unset SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Time: MIPS clocksource has been installed. NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NTFS driver 2.1.28 [Flags: R/O]. JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc. io scheduler noop registered io scheduler anticipatory registered (default) Register GPIO SPI device Serial: PNX8XXX driver $Revision: 1.2 $ pnx8xxx-uart: ttyS0 at MMIO 0xbbe4a000 (irq = 27) is a PNX8XXX pnx8xxx-uart: ttyS1 at MMIO 0xbbe4b000 (irq = 28) is a PNX8XXX natsemi dp8381x driver, version 2.1, Sept 11, 2006 originally by Donald Becker <becker@scyld.com> http://www.scyld.com/network/natsemi.html 2.4.x kernel port by Jeff Garzik, Tjeerd Mulder PCI: Enabling device 0000:00:0a.0 (0006 -> 0007) natsemi eth0: NatSemi DP8381[56] at 0x20092000 (0000:00:0a.0), 00:17:31:fb:e4:cd, IRQ 55, port TP. Driver for NAND Flash on the PNX8550 XIO bus (Mar 15 2010-17:54:27) Auto detected a >= 64MByte device on a 8 bit bus NAND device: Manufacturer ID: 0xad, Chip ID: 0x76 (Hynix NAND 64MiB 3,3V 8-bit) Scanning device for bad blocks Creating 8 MTD partitions on "NAND 64MiB 3,3V 8-bit": 0x00000000-0x00004000 : "microBTM" 0x00004000-0x00084000 : "U-Boot" 0x00084000-0x0008c000 : "Env" 0x0008c000-0x00094000 : "bbt" 0x00094000-0x00894000 : "Linux" 0x00894000-0x03b94000 : "ROMFS" 0x03c00000-0x03ff8000 : "WinCE" 0x03ff8000-0x04000000 : "Info" ehci_hcd 0000:00:09.2: EHCI Host Controller ehci_hcd 0000:00:09.2: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:09.2: irq 55, io mem 0x20093200 ehci_hcd 0000:00:09.2: USB 2.0 started, EHCI 0.95, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 4 ports detected pnx8550-ohci pnx8550-ohci: PNX8550 OHCI pnx8550-ohci pnx8550-ohci: new USB bus registered, assigned bus number 2 pnx8550-ohci pnx8550-ohci: irq 13, io mem 0x1be48000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ohci_hcd 0000:00:09.0: OHCI Host Controller ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 3 ohci_hcd 0000:00:09.0: irq 55, io mem 0x20090000 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ohci_hcd 0000:00:09.1: OHCI Host Controller ohci_hcd 0000:00:09.1: new USB bus registered, assigned bus number 4 ohci_hcd 0000:00:09.1: irq 55, io mem 0x20091000 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected USB Universal Host Controller Interface driver v3.0 Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. mice: PS/2 mouse device common for all mice i2c /dev entries driver TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Bridge firewalling registered 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> ieee80211: 802.11 data/management/control stack, git-1.1.13 ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com> eth0: DSPCFG accepted after 0 usec. eth0: link up. eth0: Setting full-duplex based on negotiated link capability. Sending DHCP requests .<5>eth0: increased tx threshold, txcfg 0xd0f01004. ..... timed out! IP-Config: Reopening network devices... eth0: DSPCFG accepted after 0 usec. eth0: link up. eth0: Setting full-duplex based on negotiated link capability. Sending DHCP requests .<5>eth0: increased tx threshold, txcfg 0xd0f01004. ., OK IP-Config: Got DHCP answer from 192.168.1.1, my address is 192.168.1.171 IP-Config: Complete: device=eth0, addr=192.168.1.171, mask=255.255.255.0, gw=192.168.1.1, host=192.168.1.171, domain=lan, nis-domain=(none), bootserver=192.168.1.1, rootserver=192.168.1.1, rootpath= Freeing unused kernel memory: 2044k freed Algorithmics/MIPS FPU Emulator v1.5 Loading profile... done Mount fstab... done Remount / read-write... done Mounting new Root. enabling SATA modules...sata_sil 0000:00:08.0: Applying R_ERR on DMA activate FIS errata fix ata1: SATA max UDMA/100 cmd 0xc0058080 ctl 0xc005808a bmdma 0xc0058000 irq 55 ata2: SATA max UDMA/100 cmd 0xc00580c0 ctl 0xc00580ca bmdma 0xc0058008 irq 55 scsi0 : sata_sil ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata1.00: ATA-8: Hitachi HTS545050B9A300, PB4OC66G, max UDMA/133 ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32) ata1.00: configured for UDMA/100 scsi1 : sata_sil ata2: SATA link down (SStatus 0 SControl 310) scsi 0:0:0:0: Direct-Access ATA Hitachi HTS54505 PB4O PQ: 0 ANSI: 5 SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB) sda: Write Protect is off SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB) sda: Write Protect is off SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sd 0:0:0:0: Attached scsi disk sda done Creating device nodes...done Setup mdev as hotplug handler... done Set log level... Populate /dev... Load luddite and gpio/mmio/rtc...Get display mode and load i2c and fb modules... Detect GPIO function...done Get System ID... Restore hotplug handler... done Restore log level... Unloading modules... CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == 801f30dc, ra == c00729e4 Oops[#1]: Cpu 0 $ 0  : 00000000 10008401 00100100 00000000 $ 4  : 00000000 00000000 c0064304 86e39ed8 $ 8  : 803896b0 86e39ee1 800a86a8 0000000c $12  : 43545262 2aab2800 00000000 2aab2800 $16  : c0072e80 c0072e74 00000087 00000480 $20  : 00000000 00000002 00000000 00000003 $24  : 00000000 2acec13c $28  : 86e38000 86e39e80 7fd49c20 c00729e4 Hi  : 00000372 Lo  : 0002c316 epc  : 801f30dc Tainted: P ra  : c00729e4 Status: 10008403 KERNEL EXL IE Cause : 1080000c BadVA : 00000000 PrId  : 00061200 Modules linked in: sysid(P) i2c_algo_IP0105 i2c_algo_IP3203 phStbRTC phStbMmio phStbGpio phStbProc lud_pnx8550 lud_core sata_sil libata Process exe (pid: 312, threadinfo=86e38000, task=811027f0) Stack : 805b0000 805b0000 0000004f 00030002 80390000 c0072f20 80390000 c00729e4 805b4e50 80099104 8008dfc0 0002ad9b 800a8844 800a86d4 805b4e50 8008a36c 86e39ec0 86e39ec0 00000000 c0072f20 00000480 86e39ec8 74536870 43545262 00000000 00000001 10008400 2aafdcb8 00000000 00000000 10008400 8008a540 00000000 80096090 7fd49de1 00000001 00d49d08 00000480 7fd49de1 00000001 ... Call Trace:[<c00729e4>][<80099104>][<8008dfc0>][<800a8844>][<800a86d4>][<8008a36c>][<8008a540>][<80096090>][<80069f00>][<80061d80>] Code: 8e030000 3c020010 34420100 <ac830000> ae020000 3c020020 34420200 ac640004 ae020004 Shutting down PNX8550 MMIO Driver Shutting down PNX8550 GPIO driver Shutting down NXP /proc entries driver done done Mount nfs root /dev/sda1... kjournald starting. Commit interval 5 seconds EXT3-fs warning: maximal mount count reached, running e2fsck is recommended EXT3 FS on sda1, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. done Switch root INIT: version 2.86 booting .udev/ already exists on the static /dev! (warning). Starting the hotplug events dispatcher: udevdudevd[425]: main: the kernel does not support inotify, udevd can't monitor rules file changes . Synthesizing the initial hotplug events...done. Waiting for /dev to be fully populated...udevd-event[493]: rename_netif: error changing netif name eth0 to eth1: Device or resource busy Registering SPI driver Register ProSLIC driver U-Boot 2011.09-00000-gf54ce7f-dirty (Dec 20 2011 - 12:36:29) DRAM: 128 MiB NAND: NAND device: Manufacturer ID: 0xad, Chip ID: 0x76 (Hynix NAND 64MiB 3,3V 8-bit) 64 MiB Bad block table at page 1120, version 0x01 Bad block table at page 1152, version 0x01 In: serial Out: serial Err: serial Net: natsemi: EEPROM contents: d008 0400 0b34 00f3 0000 0000 0000 8b80 7d98 66f2 0000 aae2 natsemi: MAC-Address: 0:17:31:FB:E4:CD dp83815#0 Welcome to the pollinux board v1.1 Hit any key to stop autoboot: 1 à U-Boot 2011.09-00000-gf54ce7f-dirty (Dec 20 2011 - 12:36:29) DRAM: 128 MiB NAND: NAND device: Manufacturer ID: 0xad, Chip ID: 0x76 (Hynix NAND 64MiB 3,3V 8-bit) 64 MiB Bad block table at page 1120, version 0x01 Bad block table at page 1152, version 0x01 In: serial Out: serial Err: serial Net: natsemi: EEPROM contents: d008 0400 0b34 00f3 0000 0000 0000 8b80 7d98 66f2 0000 aae2 natsemi: MAC-Address: 0:17:31:FB:E4:CD dp83815#0 Welcome to the pollinux board v1.1 Hit any key to stop autoboot: 0 Loading from nand0, offset 0x94000 Image Name: Elecard Linux 2.6 Created: 2011-12-07 16:01:46 UTC Image Type: MIPS Elecard Linux Kernel Image (gzip compressed) Data Size: 3233500 Bytes = 3.1 MiB Load Address: 80060000 Entry Point: 803a9000 ** Too many args (max. 16) ** ** Too many args (max. 16) ** ## Booting kernel from Legacy Image at 82000000 ... Image Name: Elecard Linux 2.6 Created: 2011-12-07 16:01:46 UTC Image Type: MIPS Elecard Linux Kernel Image (gzip compressed) Data Size: 3233500 Bytes = 3.1 MiB Load Address: 80060000 Entry Point: 803a9000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Starting kernel ... Determined physical RAM map: memory: 07000000 @ 00000000 (usable) Initrd not found or empty - disabling initrd Built 1 zonelists. Total pages: 28448 Kernel command line: console=ttyS1,38400n8 stb810_display=pal nomainapp=1 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw Primary instruction cache 16kB, physically tagged, 2-way, linesize 32 bytes. Primary data cache 16kB, 4-way, linesize 32 bytes. Synthesized TLB refill handler (23 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB modify handler fastpath (31 instructions). PID hash table entries: 512 (order: 9, 2048 bytes) Using 250.714 MHz high precision timer. Linux version 2.6.21.3PNX8550 (root@smithy) (gcc version 4.0.0 (DENX ELDK 4.0 4.0.0)) #1743 Fri Feb 11 10:49:15 OMST 2011 Setting initial splash screen display mode SD (50Hz) CPU revision is: 00061200 Determined physical RAM map: memory: 07000000 @ 00000000 (usable) Initrd not found or empty - disabling initrd Built 1 zonelists. Total pages: 28448 Kernel command line: console=ttyS1,38400n8 stb810_display=pal nomainapp=1 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw Primary instruction cache 16kB, physically tagged, 2-way, linesize 32 bytes. Primary data cache 16kB, 4-way, linesize 32 bytes. Synthesized TLB refill handler (23 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB modify handler fastpath (31 instructions). PID hash table entries: 512 (order: 9, 2048 bytes) Using 250.714 MHz high precision timer. Console: colour dummy device 80x25 Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 107648k/114688k available (2841k kernel code, 6996k reserved, 518k data, 2044k init, 0k highmem) Mount-cache hash table entries: 512 NET: Registered protocol family 16 registering PCI controller with io_map_base unset SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Time: MIPS clocksource has been installed. NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NTFS driver 2.1.28 [Flags: R/O]. JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc. io scheduler noop registered io scheduler anticipatory registered (default) Register GPIO SPI device Serial: PNX8XXX driver $Revision: 1.2 $ pnx8xxx-uart: ttyS0 at MMIO 0xbbe4a000 (irq = 27) is a PNX8XXX pnx8xxx-uart: ttyS1 at MMIO 0xbbe4b000 (irq = 28) is a PNX8XXX natsemi dp8381x driver, version 2.1, Sept 11, 2006 originally by Donald Becker <becker@scyld.com> http://www.scyld.com/network/natsemi.html 2.4.x kernel port by Jeff Garzik, Tjeerd Mulder PCI: Enabling device 0000:00:0a.0 (0006 -> 0007) natsemi eth0: NatSemi DP8381[56] at 0x20092000 (0000:00:0a.0), 00:17:31:fb:e4:cd, IRQ 55, port TP. Driver for NAND Flash on the PNX8550 XIO bus (Mar 15 2010-17:54:27) Auto detected a >= 64MByte device on a 8 bit bus NAND device: Manufacturer ID: 0xad, Chip ID: 0x76 (Hynix NAND 64MiB 3,3V 8-bit) Scanning device for bad blocks Creating 8 MTD partitions on "NAND 64MiB 3,3V 8-bit": 0x00000000-0x00004000 : "microBTM" 0x00004000-0x00084000 : "U-Boot" 0x00084000-0x0008c000 : "Env" 0x0008c000-0x00094000 : "bbt" 0x00094000-0x00894000 : "Linux" 0x00894000-0x03b94000 : "ROMFS" 0x03c00000-0x03ff8000 : "WinCE" 0x03ff8000-0x04000000 : "Info" ehci_hcd 0000:00:09.2: EHCI Host Controller ehci_hcd 0000:00:09.2: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:09.2: irq 55, io mem 0x20093200 ehci_hcd 0000:00:09.2: USB 2.0 started, EHCI 0.95, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 4 ports detected pnx8550-ohci pnx8550-ohci: PNX8550 OHCI pnx8550-ohci pnx8550-ohci: new USB bus registered, assigned bus number 2 pnx8550-ohci pnx8550-ohci: irq 13, io mem 0x1be48000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ohci_hcd 0000:00:09.0: OHCI Host Controller ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 3 ohci_hcd 0000:00:09.0: irq 55, io mem 0x20090000 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ohci_hcd 0000:00:09.1: OHCI Host Controller ohci_hcd 0000:00:09.1: new USB bus registered, assigned bus number 4 ohci_hcd 0000:00:09.1: irq 55, io mem 0x20091000 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected USB Universal Host Controller Interface driver v3.0 Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. mice: PS/2 mouse device common for all mice i2c /dev entries driver TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Bridge firewalling registered 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> ieee80211: 802.11 data/management/control stack, git-1.1.13 ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com> eth0: DSPCFG accepted after 0 usec. eth0: link up. eth0: Setting full-duplex based on negotiated link capability. Sending DHCP requests .<5>eth0: increased tx threshold, txcfg 0xd0f01004. ..... timed out! IP-Config: Reopening network devices... eth0: DSPCFG accepted after 0 usec. eth0: link up. eth0: Setting full-duplex based on negotiated link capability. Sending DHCP requests .<5>eth0: increased tx threshold, txcfg 0xd0f01004. ., OK IP-Config: Got DHCP answer from 192.168.1.1, my address is 192.168.1.171 IP-Config: Complete: device=eth0, addr=192.168.1.171, mask=255.255.255.0, gw=192.168.1.1, host=192.168.1.171, domain=lan, nis-domain=(none), bootserver=192.168.1.1, rootserver=192.168.1.1, rootpath= Freeing unused kernel memory: 2044k freed Algorithmics/MIPS FPU Emulator v1.5 Loading profile... done Mount fstab... done Remount / read-write... done Mounting new Root. enabling SATA modules...sata_sil 0000:00:08.0: Applying R_ERR on DMA activate FIS errata fix ata1: SATA max UDMA/100 cmd 0xc0058080 ctl 0xc005808a bmdma 0xc0058000 irq 55 ata2: SATA max UDMA/100 cmd 0xc00580c0 ctl 0xc00580ca bmdma 0xc0058008 irq 55 scsi0 : sata_sil ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata1.00: ATA-8: Hitachi HTS545050B9A300, PB4OC66G, max UDMA/133 ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32) ata1.00: configured for UDMA/100 scsi1 : sata_sil ata2: SATA link down (SStatus 0 SControl 310) scsi 0:0:0:0: Direct-Access ATA Hitachi HTS54505 PB4O PQ: 0 ANSI: 5 SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB) sda: Write Protect is off SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB) sda: Write Protect is off SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sd 0:0:0:0: Attached scsi disk sda done Creating device nodes...done Setup mdev as hotplug handler... done Set log level... Populate /dev... Load luddite and gpio/mmio/rtc...Get display mode and load i2c and fb modules... Detect GPIO function...done Get System ID... Restore hotplug handler... done Restore log level... Unloading modules... CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == 801f30dc, ra == c00729e4 Oops[#1]: Cpu 0 $ 0  : 00000000 10008401 00100100 00000000 $ 4  : 00000000 00000000 c0064304 86e3bed8 $ 8  : 803896b0 86e3bee1 800a86a8 0000000c $12  : 43545262 2aab2800 00000000 2aab2800 $16  : c0072e80 c0072e74 00000087 00000480 $20  : 00000000 00000002 00000000 00000003 $24  : 00000000 2acec13c $28  : 86e3a000 86e3be80 7f887c20 c00729e4 Hi  : 00000372 Lo  : 0002c316 epc  : 801f30dc Tainted: P ra  : c00729e4 Status: 10008403 KERNEL EXL IE Cause : 1080000c BadVA : 00000000 PrId  : 00061200 Modules linked in: sysid(P) i2c_algo_IP0105 i2c_algo_IP3203 phStbRTC phStbMmio phStbGpio phStbProc lud_pnx8550 lud_core sata_sil libata Process exe (pid: 312, threadinfo=86e3a000, task=81119be8) Stack : 805b0000 805b0000 0000004f 00030002 80390000 c0072f20 80390000 c00729e4 805b4e50 80099104 8008dfc0 0002ad9b 800a8844 800a86d4 805b4e50 8008a36c 86e3bec0 86e3bec0 00000000 c0072f20 00000480 86e3bec8 74536870 43545262 00000000 00000001 10008400 0f565c6e 00000000 2aabdd08 10008400 8008a540 00000000 80096090 7f887de1 00000001 00887d08 00000480 7f887de1 00000001 ... Call Trace:[<c00729e4>][<80099104>][<8008dfc0>][<800a8844>][<800a86d4>][<8008a36c>][<8008a540>][<80096090>][<80069f00>][<80061d80>] Code: 8e030000 3c020010 34420100 <ac830000> ae020000 3c020020 34420200 ac640004 ae020004 Shutting down PNX8550 MMIO Driver Shutting down PNX8550 GPIO driver Shutting down NXP /proc entries driver done done Mount nfs root /dev/sda1... kjournald starting. Commit interval 5 seconds EXT3-fs warning: maximal mount count reached, running e2fsck is recommended EXT3 FS on sda1, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. done Switch root INIT: version 2.86 booting .udev/ already exists on the static /dev! (warning). Starting the hotplug events dispatcher: udevdudevd[425]: main: the kernel does not support inotify, udevd can't monitor rules file changes . Synthesizing the initial hotplug events...done. Waiting for /dev to be fully populated...udevd-event[495]: rename_netif: error changing netif name eth0 to eth1: Device or resource busy Registering SPI driver Register ProSLIC driver U-Boot 2011.09-00000-gf54ce7f-dirty (Dec 20 2011 - 12:36:29) DRAM: 128 MiB NAND: NAND device: Manufacturer ID: 0xad, Chip ID: 0x76 (Hynix NAND 64MiB 3,3V 8-bit) 64 MiB Bad block table at page 1120, version 0x01 Bad block table at page 1152, version 0x01 In: serial Out: serial Err: serial Net: natsemi: EEPROM contents: d008 0400 0b34 00f3 0000 0000 0000 8b80 7d98 66f2 0000 aae2 natsemi: MAC-Address: 0:17:31:FB:E4:CD dp83815#0 Welcome to the pollinux board v1.1 Hit any key to stop autoboot: 0 Loading from nand0, offset 0x94000 Image Name: Elecard Linux 2.6 Created: 2011-12-07 16:01:46 UTC Image Type: MIPS Elecard Linux Kernel Image (gzip compressed) Data Size: 3233500 Bytes = 3.1 MiB Load Address: 80060000 Entry Point: 803a9000 ** Too many args (max. 16) ** ** Too many args (max. 16) ** ## Booting kernel from Legacy Image at 82000000 ... Image Name: Elecard Linux 2.6 Created: 2011-12-07 16:01:46 UTC Image Type: MIPS Elecard Linux Kernel Image (gzip compressed) Data Size: 3233500 Bytes = 3.1 MiB Load Address: 80060000 Entry Point: 803a9000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Starting kernel ... Determined physical RAM map: memory: 07000000 @ 00000000 (usable) Initrd not found or empty - disabling initrd Built 1 zonelists. Total pages: 28448 Kernel command line: console=ttyS1,38400n8 stb810_display=pal nomainapp=1 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw Primary instruction cache 16kB, physically tagged, 2-way, linesize 32 bytes. Primary data cache 16kB, 4-way, linesize 32 bytes. Synthesized TLB refill handler (23 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB modify handler fastpath (31 instructions). PID hash table entries: 512 (order: 9, 2048 bytes) Using 250.714 MHz high precision timer. Linux version 2.6.21.3PNX8550 (root@smithy) (gcc version 4.0.0 (DENX ELDK 4.0 4.0.0)) #1743 Fri Feb 11 10:49:15 OMST 2011 Setting initial splash screen display mode SD (50Hz) CPU revision is: 00061200 Determined physical RAM map: memory: 07000000 @ 00000000 (usable) Initrd not found or empty - disabling initrd Built 1 zonelists. Total pages: 28448 Kernel command line: console=ttyS1,38400n8 stb810_display=pal nomainapp=1 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw Primary instruction cache 16kB, physically tagged, 2-way, linesize 32 bytes. Primary data cache 16kB, 4-way, linesize 32 bytes. Synthesized TLB refill handler (23 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB modify handler fastpath (31 instructions). PID hash table entries: 512 (order: 9, 2048 bytes) Using 250.714 MHz high precision timer. Console: colour dummy device 80x25 Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 107648k/114688k available (2841k kernel code, 6996k reserved, 518k data, 2044k init, 0k highmem) Mount-cache hash table entries: 512 NET: Registered protocol family 16 registering PCI controller with io_map_base unset SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Time: MIPS clocksource has been installed. NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NTFS driver 2.1.28 [Flags: R/O]. JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc. io scheduler noop registered io scheduler anticipatory registered (default) Register GPIO SPI device Serial: PNX8XXX driver $Revision: 1.2 $ pnx8xxx-uart: ttyS0 at MMIO 0xbbe4a000 (irq = 27) is a PNX8XXX pnx8xxx-uart: ttyS1 at MMIO 0xbbe4b000 (irq = 28) is a PNX8XXX natsemi dp8381x driver, version 2.1, Sept 11, 2006 originally by Donald Becker <becker@scyld.com> http://www.scyld.com/network/natsemi.html 2.4.x kernel port by Jeff Garzik, Tjeerd Mulder PCI: Enabling device 0000:00:0a.0 (0006 -> 0007) natsemi eth0: NatSemi DP8381[56] at 0x20092000 (0000:00:0a.0), 00:17:31:fb:e4:cd, IRQ 55, port TP. Driver for NAND Flash on the PNX8550 XIO bus (Mar 15 2010-17:54:27) Auto detected a >= 64MByte device on a 8 bit bus NAND device: Manufacturer ID: 0xad, Chip ID: 0x76 (Hynix NAND 64MiB 3,3V 8-bit) Scanning device for bad blocks Creating 8 MTD partitions on "NAND 64MiB 3,3V 8-bit": 0x00000000-0x00004000 : "microBTM" 0x00004000-0x00084000 : "U-Boot" 0x00084000-0x0008c000 : "Env" 0x0008c000-0x00094000 : "bbt" 0x00094000-0x00894000 : "Linux" 0x00894000-0x03b94000 : "ROMFS" 0x03c00000-0x03ff8000 : "WinCE" 0x03ff8000-0x04000000 : "Info" ehci_hcd 0000:00:09.2: EHCI Host Controller ehci_hcd 0000:00:09.2: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:09.2: irq 55, io mem 0x20093200 ehci_hcd 0000:00:09.2: USB 2.0 started, EHCI 0.95, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 4 ports detected pnx8550-ohci pnx8550-ohci: PNX8550 OHCI pnx8550-ohci pnx8550-ohci: new USB bus registered, assigned bus number 2 pnx8550-ohci pnx8550-ohci: irq 13, io mem 0x1be48000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ohci_hcd 0000:00:09.0: OHCI Host Controller ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 3 ohci_hcd 0000:00:09.0: irq 55, io mem 0x20090000 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ohci_hcd 0000:00:09.1: OHCI Host Controller ohci_hcd 0000:00:09.1: new USB bus registered, assigned bus number 4 ohci_hcd 0000:00:09.1: irq 55, io mem 0x20091000 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected USB Universal Host Controller Interface driver v3.0 Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. mice: PS/2 mouse device common for all mice i2c /dev entries driver TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Bridge firewalling registered 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> ieee80211: 802.11 data/management/control stack, git-1.1.13 ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com> eth0: DSPCFG accepted after 0 usec. eth0: link up. eth0: Setting full-duplex based on negotiated link capability. Sending DHCP requests .<5>eth0: increased tx threshold, txcfg 0xd0f01004. ..... timed out! IP-Config: Reopening network devices... eth0: DSPCFG accepted after 0 usec. eth0: link up. eth0: Setting full-duplex based on negotiated link capability. Sending DHCP requests .<5>eth0: increased tx threshold, txcfg 0xd0f01004. ., OK IP-Config: Got DHCP answer from 192.168.1.1, my address is 192.168.1.171 IP-Config: Complete: device=eth0, addr=192.168.1.171, mask=255.255.255.0, gw=192.168.1.1, host=192.168.1.171, domain=lan, nis-domain=(none), bootserver=192.168.1.1, rootserver=192.168.1.1, rootpath= Freeing unused kernel memory: 2044k freed Algorithmics/MIPS FPU Emulator v1.5 Loading profile... done Mount fstab... done Remount / read-write... done Mounting new Root. enabling SATA modules...sata_sil 0000:00:08.0: Applying R_ERR on DMA activate FIS errata fix ata1: SATA max UDMA/100 cmd 0xc0058080 ctl 0xc005808a bmdma 0xc0058000 irq 55 ata2: SATA max UDMA/100 cmd 0xc00580c0 ctl 0xc00580ca bmdma 0xc0058008 irq 55 scsi0 : sata_sil ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata1.00: ATA-8: Hitachi HTS545050B9A300, PB4OC66G, max UDMA/133 ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32) ata1.00: configured for UDMA/100 scsi1 : sata_sil ata2: SATA link down (SStatus 0 SControl 310) scsi 0:0:0:0: Direct-Access ATA Hitachi HTS54505 PB4O PQ: 0 ANSI: 5 SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB) sda: Write Protect is off SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB) sda: Write Protect is off SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sd 0:0:0:0: Attached scsi disk sda done Creating device nodes...done Setup mdev as hotplug handler... done Set log level... Populate /dev... Load luddite and gpio/mmio/rtc...Get display mode and load i2c and fb modules... Detect GPIO function...done Get System ID... Restore hotplug handler... done Restore log level... Unloading modules... CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == 801f30dc, ra == c00729e4 Oops[#1]: Cpu 0 $ 0  : 00000000 10008401 00100100 00000000 $ 4  : 00000000 00000000 c0064304 86e39ed8 $ 8  : 803896b0 86e39ee1 800a86a8 0000000c $12  : 43545262 2aab2800 00000000 2aab2800 $16  : c0072e80 c0072e74 00000087 00000480 $20  : 00000000 00000002 00000000 00000003 $24  : 00000000 2acec13c $28  : 86e38000 86e39e80 7fc64c20 c00729e4 Hi  : 00000372 Lo  : 0002c316 epc  : 801f30dc Tainted: P ra  : c00729e4 Status: 10008403 KERNEL EXL IE Cause : 1080000c BadVA : 00000000 PrId  : 00061200 Modules linked in: sysid(P) i2c_algo_IP0105 i2c_algo_IP3203 phStbRTC phStbMmio phStbGpio phStbProc lud_pnx8550 lud_core sata_sil libata Process exe (pid: 312, threadinfo=86e38000, task=811027f0) Stack : 00000003 80098f84 0000004f 00030002 80390000 c0072f20 80390000 c00729e4 805b4e50 80099104 8008dfc0 0002ad9b 800a8844 800a86d4 805b4e50 8008a36c 86e39ec0 86e39ec0 00000000 c0072f20 00000480 86e39ec8 74536870 43545262 00000200 00000001 10008400 10002eb8 2aafdcb8 004068d0 10008400 8008a540 00000000 80096090 7fc64de1 00000001 00c64d08 00000480 7fc64de1 00000001 ... Call Trace:[<80098f84>][<c00729e4>][<80099104>][<8008dfc0>][<800a8844>][<800a86d4>][<8008a36c>][<8008a540>][<80096090>][<80069f00>][<80061d80>] Code: 8e030000 3c020010 34420100 <ac830000> ae020000 3c020020 34420200 ac640004 ae020004 Shutting down PNX8550 MMIO Driver Shutting down PNX8550 GPIO driver Shutting down NXP /proc entries driver done done Mount nfs root /dev/sda1... kjournald starting. Commit interval 5 seconds EXT3-fs warning: maximal mount count reached, running e2fsck is recommended EXT3 FS on sda1, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. done Switch root INIT: version 2.86 booting .udev/ already exists on the static /dev! (warning). Starting the hotplug events dispatcher: udevdudevd[425]: main: the kernel does not support inotify, udevd can't monitor rules file changes . Synthesizing the initial hotplug events...done. Waiting for /dev to be fully populated...udevd-event[494]: rename_netif: error changing netif name eth0 to eth1: Device or resource busy Registering SPI driver Register ProSLIC driver Setting parameters of disc: (none). Setting the system clock. Cannot access the Hardware Clock via any known method. Use the --debug option to see the details of our search for an access method. Unable to set System Clock to: Sat Jan 1 00:01:40 UTC 2000 (warning). Activating swap...done. Setting the system clock. Cannot access the Hardware Clock via any known method. Use the --debug option to see the details of our search for an access method. Unable to set System Clock to: Sat Jan 1 00:01:41 UTC 2000 (warning). Cleaning up ifupdown.... Loading kernel modules...done. Checking file systems...fsck 1.41.3 (12-Oct-2008) done. Setting kernel variables (/etc/sysctl.conf)...done. Mounting local filesystems...kjournald starting. Commit interval 5 seconds EXT3-fs warning: maximal mount count reached, running e2fsck is recommended EXT3 FS on sda2, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on sda3, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. done. Activating swapfile swap...done. Setting up networking.... Configuring network interfaces...done. Luddite version 3, exported Mon Apr 25 10:40:08 BST 2005 TM0: detected clock 270000000 lud_core: Registering devfs device 0/lud TM1: detected clock 270000000 lud_core: Registering devfs device 1/lud NXP /proc entries driver (Aug 13 2007-11:59:40) dspinfo: Initialising DSP Info Driver PNX8550 MMIO Driver (Aug 13 2007-11:59:38) dspmem: Initialising DSP memory Driver U-Boot 2011.09-00000-gf54ce7f-dirty (Dec 20 2011 - 12:36:29) DRAM: 128 MiB NAND: NAND device: Manufacturer ID: 0xad, Chip ID: 0x76 (Hynix NAND 64MiB 3,3V 8-bit) 64 MiB Bad block table at page 1120, version 0x01 Bad block table at page 1152, version 0x01 In: serial Out: serial Err: serial Net: natsemi: EEPROM contents: d008 0400 0b34 00f3 0000 0000 0000 8b80 7d98 66f2 0000 aae2 natsemi: MAC-Address: 0:17:31:FB:E4:CD dp83815#0 Welcome to the pollinux board v1.1 Hit any key to stop autoboot: 0 Loading from nand0, offset 0x94000 Image Name: Elecard Linux 2.6 Created: 2011-12-07 16:01:46 UTC Image Type: MIPS Elecard Linux Kernel Image (gzip compressed) Data Size: 3233500 Bytes = 3.1 MiB Load Address: 80060000 Entry Point: 803a9000 ** Too many args (max. 16) ** ** Too many args (max. 16) ** ## Booting kernel from Legacy Image at 82000000 ... Image Name: Elecard Linux 2.6 Created: 2011-12-07 16:01:46 UTC Image Type: MIPS Elecard Linux Kernel Image (gzip compressed) Data Size: 3233500 Bytes = 3.1 MiB Load Address: 80060000 Entry Point: 803a9000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Starting kernel ... Determined physical RAM map: memory: 07000000 @ 00000000 (usable) Initrd not found or empty - disabling initrd Built 1 zonelists. Total pages: 28448 Kernel command line: console=ttyS1,38400n8 stb810_display=pal nomainapp=1 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw Primary instruction cache 16kB, physically tagged, 2-way, linesize 32 bytes. Primary data cache 16kB, 4-way, linesize 32 bytes. Synthesized TLB refill handler (23 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB modify handler fastpath (31 instructions). PID hash table entries: 512 (order: 9, 2048 bytes) Using 250.714 MHz high precision timer. Linux version 2.6.21.3PNX8550 (root@smithy) (gcc version 4.0.0 (DENX ELDK 4.0 4.0.0)) #1743 Fri Feb 11 10:49:15 OMST 2011 Setting initial splash screen display mode SD (50Hz) CPU revision is: 00061200 Determined physical RAM map: memory: 07000000 @ 00000000 (usable) Initrd not found or empty - disabling initrd Built 1 zonelists. Total pages: 28448 Kernel command line: console=ttyS1,38400n8 stb810_display=pal nomainapp=1 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw ip=192.168.100.215 root=/dev/sda1 rw Primary instruction cache 16kB, physically tagged, 2-way, linesize 32 bytes. Primary data cache 16kB, 4-way, linesize 32 bytes. Synthesized TLB refill handler (23 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB modify handler fastpath (31 instructions). PID hash table entries: 512 (order: 9, 2048 bytes) Using 250.714 MHz high precision timer. Console: colour dummy device 80x25 Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 107648k/114688k available (2841k kernel code, 6996k reserved, 518k data, 2044k init, 0k highmem) Mount-cache hash table entries: 512 NET: Registered protocol family 16 registering PCI controller with io_map_base unset SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Time: MIPS clocksource has been installed. NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NTFS driver 2.1.28 [Flags: R/O]. JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc. io scheduler noop registered io scheduler anticipatory registered (default) Register GPIO SPI device Serial: PNX8XXX driver $Revision: 1.2 $ pnx8xxx-uart: ttyS0 at MMIO 0xbbe4a000 (irq = 27) is a PNX8XXX pnx8xxx-uart: ttyS1 at MMIO 0xbbe4b000 (irq = 28) is a PNX8XXX natsemi dp8381x driver, version 2.1, Sept 11, 2006 originally by Donald Becker <becker@scyld.com> http://www.scyld.com/network/natsemi.html 2.4.x kernel port by Jeff Garzik, Tjeerd Mulder PCI: Enabling device 0000:00:0a.0 (0006 -> 0007) natsemi eth0: NatSemi DP8381[56] at 0x20092000 (0000:00:0a.0), 00:17:31:fb:e4:cd, IRQ 55, port TP. Driver for NAND Flash on the PNX8550 XIO bus (Mar 15 2010-17:54:27) Auto detected a >= 64MByte device on a 8 bit bus NAND device: Manufacturer ID: 0xad, Chip ID: 0x76 (Hynix NAND 64MiB 3,3V 8-bit) Scanning device for bad blocks Creating 8 MTD partitions on "NAND 64MiB 3,3V 8-bit": 0x00000000-0x00004000 : "microBTM" 0x00004000-0x00084000 : "U-Boot" 0x00084000-0x0008c000 : "Env" 0x0008c000-0x00094000 : "bbt" 0x00094000-0x00894000 : "Linux" 0x00894000-0x03b94000 : "ROMFS" 0x03c00000-0x03ff8000 : "WinCE" 0x03ff8000-0x04000000 : "Info" ehci_hcd 0000:00:09.2: EHCI Host Controller ehci_hcd 0000:00:09.2: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:09.2: irq 55, io mem 0x20093200 ehci_hcd 0000:00:09.2: USB 2.0 started, EHCI 0.95, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 4 ports detected pnx8550-ohci pnx8550-ohci: PNX8550 OHCI pnx8550-ohci pnx8550-ohci: new USB bus registered, assigned bus number 2 pnx8550-ohci pnx8550-ohci: irq 13, io mem 0x1be48000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ohci_hcd 0000:00:09.0: OHCI Host Controller ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 3 ohci_hcd 0000:00:09.0: irq 55, io mem 0x20090000 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ohci_hcd 0000:00:09.1: OHCI Host Controller ohci_hcd 0000:00:09.1: new USB bus registered, assigned bus number 4 ohci_hcd 0000:00:09.1: irq 55, io mem 0x20091000 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected USB Universal Host Controller Interface driver v3.0 Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. mice: PS/2 mouse device common for all mice i2c /dev entries driver TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Bridge firewalling registered 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> ieee80211: 802.11 data/management/control stack, git-1.1.13 ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com> eth0: DSPCFG accepted after 0 usec. eth0: link up. eth0: Setting full-duplex based on negotiated link capability. Sending DHCP requests .<5>eth0: increased tx threshold, txcfg 0xd0f01004. ..... timed out! IP-Config: Reopening network devices... eth0: DSPCFG accepted after 0 usec. eth0: link up. eth0: Setting full-duplex based on negotiated link capability. Sending DHCP requests .<5>eth0: increased tx threshold, txcfg 0xd0f01004. ., OK IP-Config: Got DHCP answer from 192.168.1.1, my address is 192.168.1.171 IP-Config: Complete: device=eth0, addr=192.168.1.171, mask=255.255.255.0, gw=192.168.1.1, host=192.168.1.171, domain=lan, nis-domain=(none), bootserver=192.168.1.1, rootserver=192.168.1.1, rootpath= Freeing unused kernel memory: 2044k freed Algorithmics/MIPS FPU Emulator v1.5 Loading profile... done Mount fstab... done Remount / read-write... done Mounting new Root. enabling SATA modules...sata_sil 0000:00:08.0: Applying R_ERR on DMA activate FIS errata fix ata1: SATA max UDMA/100 cmd 0xc0058080 ctl 0xc005808a bmdma 0xc0058000 irq 55 ata2: SATA max UDMA/100 cmd 0xc00580c0 ctl 0xc00580ca bmdma 0xc0058008 irq 55 scsi0 : sata_sil ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata1.00: ATA-8: Hitachi HTS545050B9A300, PB4OC66G, max UDMA/133 ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32) ata1.00: configured for UDMA/100 scsi1 : sata_sil ata2: SATA link down (SStatus 0 SControl 310) scsi 0:0:0:0: Direct-Access ATA Hitachi HTS54505 PB4O PQ: 0 ANSI: 5 SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB) sda: Write Protect is off SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB) sda: Write Protect is off SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sd 0:0:0:0: Attached scsi disk sda done Creating device nodes...done Setup mdev as hotplug handler... done Set log level... Populate /dev... Load luddite and gpio/mmio/rtc...Get display mode and load i2c and fb modules... Detect GPIO function...done Get System ID... Restore hotplug handler... done Restore log level... Unloading modules... CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == 801f30dc, ra == c00729e4 Oops[#1]: Cpu 0 $ 0  : 00000000 10008401 00100100 00000000 $ 4  : 00000000 00000000 c0064304 8110fed8 $ 8  : 803896b0 8110fee1 800a86a8 0000000c $12  : 43545262 2aab2800 00000000 2aab2800 $16  : c0072e80 c0072e74 00000087 00000480 $20  : 00000000 00000002 00000000 00000003 $24  : 00000000 2acec13c $28  : 8110e000 8110fe80 7fec0c20 c00729e4 Hi  : 00000372 Lo  : 0002c316 epc  : 801f30dc Tainted: P ra  : c00729e4 Status: 10008403 KERNEL EXL IE Cause : 1080000c BadVA : 00000000 PrId  : 00061200 Modules linked in: sysid(P) i2c_algo_IP0105 i2c_algo_IP3203 phStbRTC phStbMmio phStbGpio phStbProc lud_pnx8550 lud_core sata_sil libata Process exe (pid: 312, threadinfo=8110e000, task=86d9b7f0) Stack : 805b0000 805b0000 0000004f 00030002 80390000 c0072f20 80390000 c00729e4 805b4e50 80099104 8008dfc0 00000000 800a8844 800a86d4 805b4e50 8008a36c 8110fec0 8110fec0 00000000 c0072f20 00000480 8110fec8 74536870 43545262 00000000 00000012 10008400 0000020b 0040369c 2aabdd08 10008400 8008a540 00000000 80096090 7fec0de1 00000001 00ec0d08 00000480 7fec0de1 00000001 ... Call Trace:[<c00729e4>][<80099104>][<8008dfc0>][<800a8844>][<800a86d4>][<8008a36c>][<8008a540>][<80096090>][<80069f00>][<80061d80>] Code: 8e030000 3c020010 34420100 <ac830000> ae020000 3c020020 34420200 ac640004 ae020004 Shutting down PNX8550 MMIO Driver Shutting down PNX8550 GPIO driver Shutting down NXP /proc entries driver done done Mount nfs root /dev/sda1... kjournald starting. Commit interval 5 seconds EXT3-fs warning: maximal mount count reached, running e2fsck is recommended EXT3 FS on sda1, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. done Switch root INIT: version 2.86 booting .udev/ already exists on the static /dev! (warning). Starting the hotplug events dispatcher: udevdudevd[425]: main: the kernel does not support inotify, udevd can't monitor rules file changes . Synthesizing the initial hotplug events...done. Waiting for /dev to be fully populated...udevd-event[493]: rename_netif: error changing netif name eth0 to eth1: Device or resource busy Registering SPI driver Register ProSLIC driver Setting parameters of disc: (none). Setting the system clock. Cannot access the Hardware Clock via any known method. Use the --debug option to see the details of our search for an access method. Unable to set System Clock to: Sat Jan 1 00:02:29 UTC 2000 (warning). Activating swap...done. Setting the system clock. Cannot access the Hardware Clock via any known method. Use the --debug option to see the details of our search for an access method. Unable to set System Clock to: Sat Jan 1 00:02:31 UTC 2000 (warning). Cleaning up ifupdown.... Loading kernel modules...done. Checking file systems...fsck 1.41.3 (12-Oct-2008) done. Setting kernel variables (/etc/sysctl.conf)...done. Mounting local filesystems...kjournald starting. Commit interval 5 seconds EXT3-fs warning: maximal mount count reached, running e2fsck is recommended EXT3 FS on sda2, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on sda3, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. done. Activating swapfile swap...done. Setting up networking.... Configuring network interfaces...done. Luddite version 3, exported Mon Apr 25 10:40:08 BST 2005 TM0: detected clock 270000000 lud_core: Registering devfs device 0/lud TM1: detected clock 270000000 lud_core: Registering devfs device 1/lud NXP /proc entries driver (Aug 13 2007-11:59:40) dspinfo: Initialising DSP Info Driver PNX8550 MMIO Driver (Aug 13 2007-11:59:38) dspmem: Initialising DSP memory Driver

Samba

erst mal mounten: mkdir /mnt/share

/etc/fstab

/dev/sda3 /mnt/share ext3 defaults 0 0


/etc/samba/smb.conf

[share]

path=/mnt/share

browseable=yes

writeable=yes

upstream: 3,69 MB/s

downstream: 3,30 MB/s

X11

Ganz wichtig: /etc/hosts anlegen und 127.0.0.1 localhost eintragen!

apt-get install xdm

apt-get install x11-apps

vim /etc/ssh/sshd_config

--> hier X11Forwarding yes hinzufügen

VDR

Suchlauf:

w_scan -f c -o 6 >/etc/vdr/channels.conf

Das c steht für Cable-Tuner.

danach:

mkdir /var/lib/video.00

sonst startet vdr nicht.

vdr

epg-wird aus dem DVB-C-Anschluss geladen.

vdradmin-am

Proxy einrichten, damit der Recorder fernbedient werden kann:

ln -s /etc/apache2/mods-available/proxy.load /etc/apache2/mods-enabled/proxy.load

ln -s /etc/apache2/mods-available/proxy.conf /etc/apache2/mods-enabled/proxy.conf

/etc/init.d/apache2 restart

vdr-admin starten:

/etc/init.d/vdradmin-am start

Nutzername/Passwort: vim /etc/vdradmin-am/vdradmind.conf (linvdr/linvdr)

Host erlauben: vim /var/lib/vdr/svdrphosts.conf

vdr muss laufen und vdradmin-am. Dazu müsse die Berechtigung der Aufnahmeordner gesetzt werden:

chmod 777 /mnt/

chmod 777 /mnt/media/recordings

chmod 777 /mnt/recordings

/etc/init.d/vdr restart

/etc/init.d/vdradmin-am restart